WAGO 750-370 страница 208 Скачать руководство пользователя

Страница: 208 / 222

208 Appendix

WAGO-I/O-System 750

750-370 PROFINET IO Fieldbus Coupler

Manual

Version 2.0.0

Table 175: Additional Error Information Fault Type “Internal Bus Fault 0x100“

Fault type “Internal bus fault (0x0100)“
Extended

fault type

Additional

value

Description

0x0001

0x00000106

The module configuration that has been determined on the

internal bus after AUTORESET differs from the configuration

performed before the internal bus fault occurred.

0x0003

0x01100300

Internal bus protocol fault due to internal bus RESET fault.

0x0003

0x01110300

Internal bus protocol fault due to command fault.

0x0003

0x01120300

Internal bus protocol fault due to faulty input data.

0x0003

0x01140300

Internal bus protocol fault due to faulty output data.

0x0003

0x01180300

Internal bus protocol fault caused by timeout.

0x0004

0x011204xx

Internal bus interruption after module slot xx (xx = 0 … 128).

0x0005

0x011005xx

Internal bus initializing fault because of an abortive register

communication with the module on slot xx (xx = 1 … 128).

Invalid module configurations are reported via manufacturer specific fault of type

101

. Additional fault information is available in the following table.

Table 176: Additional Error Information Fault Type “Configuration fault (0x0101)”

Fault type “Configuration fault (0x0101)”
Extended

fault type

Additional

value

Description

0x0012

0xC0018012

The bit offset for the inputs of the module is not allowed.

0x0013

0xC0018013

The bit offset for the inputs of the module exceed the maximum

offset.

0x0015

0xC0018015

The configured data length for the input module is smaller than

expected.

0x0016

0xC0018016

The configured data length for the input module is larger than

expected.

0x0017

0xC0018017

The configured data length for the input module is not allowed.

0x0022

0xC0018022

The bit offset for the output of the module is not allowed.

0x0023

0xC0018023

The bit offset for the output of the module exceeds the maximum

offset.

0x0025

0xC0018025

The configured data length for the output module is smaller than

expected.

0x0026

0xC0018026

The configured data length for the output module is larger than

expected.

0x0027

0xC0018027

The configured data length for the output module is not allowed.

If a fault occurs on the internal data bus system when the PNIO connection is

being established and if auto reset of the internal data bus was set by the station

proxy, then the PNIO connection must be interrupted and re-established in order

to set the parameters of the connected I/O modules. The reconfiguration request is

triggered by a manufacturer specific fault of type 102

. Additional fault

information is available in the following table.

Содержание 750-370































































































































































































































Результаты поиска

Содержание 750-370

Отзывы:

Похожие инструкции для 750-370

Бренды по названию

Популярные бренды

WAGO 750-370, Руководство пользователя

Результаты поиска

Содержание 750-370

Отзывы:

Похожие инструкции для 750-370

Бренды по названию

Популярные бренды