manualshive.com logo in svg

WAGNER Jaguar, Руководство по эксплуатации

Поделиться
Скачать
WAGNER Jaguar Скачать руководство пользователя страница 41

41

150 cm

3

 - 300 cm

3

 

OPERATING MANUAL

VERSION 05/2015

ORDER NUMBER DOC2340282

8.1.3 

DECOMMISSIONING AND CLEANING

8. Fully assemble the system.
9. Check fi ll level of the separating agent   Chapter 8.2.4.
10. Fill the system with fl ushing agent in accordance with Chapter 8.2.6.

When storing the device for longer periods of time, it is necessary to thoroughly clean it 
and protect it from corrosion. Replace the water or solvent in the product pump with a 
suitable preservative, fi ll separating agent cup with separating agent.

Procedure:

1. Carry out points 1 to 9 of Chapter 8.1.3 "Decommission and clean".
2. Fill the system with preservative in accordance with Chapter 8.2.6.
3. Empty the pump in a controlled manner in accordance with Chapter 8.2.5 and seal the 

openings.

8.1.4 

LONG-TERM STORAGE

The device should be cleaned for maintenance purposes. Ensure that no remaining 
product dries on and sticks to the device.

1. Carry out work interruption   Chapter 7.5.
2. Carry out basic fl ushing   in accordance with Chapter 7.6.
3. Empty the pump in a controlled manner   in accordance with Chapter 8.2.5.
4. Maintain the gun according to the operating manual.
5. Clean and check the suction system and the suction fi lter.
6. When using a material fi lter, check fi lter insert and fi lter housing and clean or replace 

them.   Chapter 8.2.7.

7. Clean the outside of the system.

Brittle fi lter pressure regulator! 

The tank on the fi lter pressure regulator becomes brittle through 
contact with solvents and can burst.
Flying parts can cause injury.

  Do not clean the tank on the fi lter pressure regulator with 

solvents.

WARNING

Gas mixtures can explode if there is an incompletely filled 
pump!

Danger to life from fl ying parts.
Ignition of potentially explosive surrounding atmosphere.

  Ensure that the pump and suction system are always completely 

filled with fl ushing agent or working material.

  Do not spray the device empty after cleaning.

WARNING

Содержание Jaguar





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды