manualshive.com logo in svg

Wacker Neuson RD 12A, Руководство оператора

Поделиться
Скачать
Wacker Neuson RD 12A Скачать руководство пользователя страница 70

Basic Troubleshooting

RD 12A

70

                                       

wc_tx001558gb.fm

6

Basic Troubleshooting

Problem / Symptom

Reason / Remedy

ENGINE DOES NOT 

START

• Fuel tank empty.
• Wrong type of fuel.
• Old fuel. Drain tank, change fuel filter and fill with fresh fuel.
• Fuel system not primed.
• Fuel filter restricted or plugged.  Replace filter.
• Battery connections loose or corroded.  Battery dead.
• Air cleaner element plugged.
• Starter motor defective.
• Fuel solenoids on engine inoperative. 
• Starter relay inoperative.
• Electrical connections loose or broken.

ENGINE STOPS BY 

ITSELF

• Fuel tank empty.
• Fuel filter plugged.
• Fuel lines broken or loose.
• No spark. 

NO VIBRATION

• Defective switch or poor connection.
• Solenoid on vibration valve damaged or disconnected.
• Exciter assembly damaged.
• Exciter motor coupling damaged or broken.
• Exciter motor damaged.
• Exciter pump damaged.
• Exciter bearings damaged.

NO TRAVEL or 

TRAVEL ONLY IN 
ONE DIRECTION

• Pin sheared on forward/reverse control.
• Control cable loose or broken.
• Drive motor damaged.
• Drive pump damaged.
• Defective relief valve or valves.

NO STEERING

• Steering cylinder damaged.
• Steering unit damaged.
• Steering relief valve stuck or damaged.
• Articulation joint lockarm engaged.

Содержание RD 12A











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды