manualshive.com logo in svg

Wacker Neuson RD 12A, Руководство оператора

Поделиться
Скачать
Wacker Neuson RD 12A Скачать руководство пользователя страница 66

Maintenance

RD 12A

66

                                       

wc_tx001557gb.fm

•

Drain the fuel tank and drain the water tank. If ballast was added 
to the rear drum, also drain the rear drum. 

•

Change the engine oil.

•

Remove the spark plugs and pour approximately 3 ml (1 ounce) 
of SAE 30W oil into each engine cylinder through the spark plug 
opening. 

•

Re-install the spark plugs. Leave the ignition wires disconnected 
to prevent the engine from starting. Crank the engine for one or 
two seconds to distribute the oil inside the engine cylinders. Con-
nect the ignition wires.

•

Clean the entire roller and engine compartment.

•

Remove dirt from the cooling fins on the engine cylinders and on 
the blower housing.

•

Set the lockarm to secure the roller halves together.

•

Remove the battery from the machine and charge it periodically.

•

Cover the entire machine and place it in a dry, protected area.

  

Содержание RD 12A











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды