manualshive.com logo in svg

Wacker Neuson RD 12A, Руководство оператора

Поделиться
Скачать
Wacker Neuson RD 12A Скачать руководство пользователя страница 65

RD 12A

Maintenance

wc_tx001557gb.fm

65

5.14 Changing the Hydraulic Oil & Filter

All oils eventually shear or thin out with use, reducing their lubricating
ability. In addition, heat, oxidation, and contamination may cause the
formation of sludge, gum, or varnish in the system. For these reasons,
it is important to change the hydraulic oil at specified intervals. See

Maintenance Schedule.

5.14.1 Remove the filler cap/filter cartridge from top of the hydraulic tank.
5.14.2 Remove the drain plug on the drain hose and allow the hydraulic fluid

to drain.

Note:

 

In the interests of environmental protection, place plastic

sheeting and a container under the machine to collect the liquid which
drains off. Dispose of this liquid properly.

5.14.3 Unscrew the return line filter and replace the filter cartridge.
5.14.4 Install the drain plug on the drain hose.
5.14.5 Fill the hydraulic tank through the filler port with clean hydraulic fluid.
5.14.6 Bleed the hydraulic system. See section

 Bleeding the Hydraulic

System.

5.15 Bleeding the Hydraulic System

5.15.1 Fill the hydraulic system with clean hydraulic oil until it is visible at the

middle level or higher in the sightglass. Do not re-use used hydraulic
oil.

5.15.2 Disconnect the spark plug wires to prevent the engine from starting.
5.15.3 Crank engine 5–10 seconds. This will allow the oil to fill the inlet lines.
5.15.4 Reconnect the spark plug wires.
5.15.5 Place forward/reverse control in the NEUTRAL position. Start the

engine and run the machine at idle for 3–4 minutes.

5.15.6 With the engine still running at idle, move the machine slowly back and

forth from forward to reverse for a short time to bleed air trapped in
drive circuit.

5.15.7 Switch the engine to high idle for 15–20 seconds. Return to low idle for

1 minute. Repeat 2–3 times to bleed the remaining air from the
hydraulic lines.

5.15.8 Check the hydraulic oil level and add oil as required.

Note:

 

If the drive pump chatters or operation is noisy, turn the machine

off and check for air leaks in the inlet line of the charge pump.

5.16

Long-Term Storage

If machine is to be stored for more than 30 days:

Содержание RD 12A











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды