manualshive.com logo in svg

Wacker Neuson RD 12A, Руководство оператора

Поделиться
Скачать
Wacker Neuson RD 12A Скачать руководство пользователя страница 30

Operation

RD 12A

30

                                       

wc_tx001071gb.fm

If the ROPS has been removed from the machine, it must be
reinstalled before the machine is used. When reinstalling the ROPS,
use the original nuts and bolts and tighten the bolts to the specified
torques.
Do not weld or drill into the ROPS. Drilling or welding on the ROPS will
nullify the ROPS certification.

4.8

Rotating Beacon (if equipped)

See Graphic: wc_gr002957

The rotating beacon 

(34)

 powers up when the ignition switch is turned

to the ON position.

4.9

Backup Alarm (if equipped)

The backup alarm is located on the rear of the machine.
Start the engine and move the forward/reverse control to the reverse
position. The backup alarm should sound immediately. The backup
alarm will continue to sound until the forward/reverse control is moved
to the neutral position or to the forward position.
If the backup alarm does not sound, make the necessary repairs
before using the roller.

wc_gr002957

b

a

34

Содержание RD 12A











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды