Wacker Neuson RD 12A Скачать руководство пользователя страница 22

Страница: 22 / 106

Lifting and Transporting

RD 12A

wc_tx001556gb.fm

3.2

Tying Down and Transporting the Machine

See Graphic: wc_gr003455

Lock the articulated joint lockarm

Refer to section

Articulation Joint

Lockarm

for information.

When transporting the machine, place blocks in front of and behind
each drum and use the front and rear tie-down points

(a)

provided to

securely fasten the machine to the trailer (two places). Secure the
machine by attaching steel ropes or chains to the tie down points

(a)

Note:

The transmission is normally braked when the engine is off, or

when the hydraulic system is not functioning, unless there is a fault
and/or the parking brakes have been manually disabled.

NOTICE

: Do not position ropes or chains across the machine frame or

the articulated joint when tying down the machine. Damage to the
machine may occur.

NOTICE

: Do not use complete deflection of shock mounts when tying

down the machine. Damage to the shock mounts may occur.

NOTICE

: Do not leave the machine tied down for extended periods of

time (except when transporting the machine). Damage to the shock
mounts may occur.

wc_gr003455

Содержание RD 12A











































































































Результаты поиска

Содержание RD 12A

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson RD 12A, Руководство оператора

Результаты поиска

Содержание RD 12A

Отзывы:

Бренды по названию

Популярные бренды