Wacker Neuson RD 12A Скачать руководство пользователя страница 41

Страница: 41 / 106

RD 12A

Operation

wc_tx001071gb.fm

4.19 Stopping/Parking

See Graphic: wc_gr002953

4.19.1 Stop the machine on a flat surface with a suitable load bearing

capacity.

4.19.2 Turn the vibration off by pressing the vibration control button

(10)

the forward/reverse lever

(15)

4.19.3 Press the water spray switch to the OFF position

(61)

4.19.4 Set the forward/reverse control

(15)

to the NEUTRAL position.

4.19.5 Return the engine throttle to idle by pressing the lower half of the

throttle switch

(54)

and allow the engine to cool down.

4.19.6 Set the parking brake

(42)

. To set the parking brake, pull the brake

lever up until the brake pad engages the drum. To release the brake,
lower the brake lever. Always set the parking brake before leaving the
machine.

Note:

The parking brake engages the rear drum only

4.19.7 Stop the engine by turning the ignition switch

(55)

to the OFF position

If the vehicle constitutes a hazard or obstacle to traffic when parked, it
should be marked with signs, lights, and other warnings.
If the machine must be parked on a sloping surface, chock the drums
with wedges to prevent any vehicle movement.

WARNING

wc_gr002953

Содержание RD 12A











































































































Результаты поиска

Содержание RD 12A

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson RD 12A, Руководство оператора

Результаты поиска

Содержание RD 12A

Отзывы:

Бренды по названию

Популярные бренды