background image

2 Introduction

100_0000_0013.fm

7

2

Introduction

2.1

Use of the manual

This manual is considered as part of the machine and must be kept in a safe 
place throughout the entire lifecycle. This manual must be handed over to every 
subsequent owner or user of the machine.

2.2

Storing the manual

This manual is part of the machine and must be stored in the immediate vicinity 
of the machine and be available to staff at all times.

In the case of loss or if a second copy of this manual is required, there are two 
options for obtaining a replacement:

Download from the Internet - 

www.wackerneuson.com

Contact your Wacker Neuson representative.

2.3

Accident prevention regulations

Local accident prevention regulations and national occupational safety provi-
sions apply in addition to the notes and safety information contained in this man-
ual.

2.4

Further information

This manual is valid for different machine types from a product range. As such, 
some illustrations may differ from the appearance of your machine. Variant-de-
pendent components may also be described that are not included in the delivery.

The information contained in this manual is based on machines which have been 
manufactured at the time of printing. Wacker Neuson reserves the right to amend 
this information without notification.

It must be ensured that any potential amendments or supplements from the man-
ufacturer are included immediately in this manual.

Содержание DPU 4545





























































































Отзывы: