25
Important Notice
All VT7600 series controls are
for use as operating controls
only and are not safety
devices. These
instruments have undergone rigorous
tests and verifications prior to shipment to
ensure proper and reliable operation in
the field. Whenever a control failure could
lead to personal injury and/or loss of
property, it becomes the responsibility of
the user / installer / electrical system
designer to incorporate safety devices (
such as relays, flow switch, thermal
protections, etc…) and/or alarm system to
protect the entire system against such
catastrophic failures. Tampering of the
devices or miss application of the device
will void warranty.
Specifications
Thermostat power requirements: 19-30 Vac 50 or 60 Hz; 2 VA ( RC & C ) Class 2
RC to RH jumper 2.0 Amps 48 VA maximum
Operating conditions: 0 °C to 50 °C ( 32 °F to 122 °F )
0% to 95% R.H. non-condensing
Storage conditions: -30 °C to 50 °C ( -22 °F to 122 °F )
0% to 95% R.H. non-condensing
Temperature sensor: Local 10 K NTC thermistor
Resolution: Temperature: ± 0.1 °C (± 0.2 °F)
Humidity: ± 0.1%
Control accuracy: Temp: ± 0.5 ° C ( ± 0.9 °F ) @ 21 °C ( 70 °F ) typ. calibrated
Humidity: ± 5% RH from 20 to 0% RH at 50 to 90°F (10 to 32°C)
Humidification setpoint range: 10% RH to 90% RH
Dehumidification setpoint range: 15% RH to 95% RH
Occupied and unoccupied setpoint range cooling: 12.0 to 37.5 °C ( 54 to 100 °F )
Occupied and unoccupied setpoint range heating: 4.5 °C to 32 °C ( 40 °F to 90 °F )
Room and outdoor air temperature range -40 °C to 50 °C ( -40 °F to 122 °F )
Proportional band for room temperature control: Factory set, heating and cooling at: 1.1°C ( 2.0°F )
Digital input: Relay dry contact only across C terminal to DI1
Analog high limit and remote humidity inputs 0 to 10 Vdc into 10K
Ω
input load
Contact output rating: Each relay output: ( Y1, Y2, G, W1, W2 & AU )
30 Vac, 1 Amp. maximum
30 Vac, 3 Amp. in-rush
Humidification analog output rating: 0 to 10 Vdc into 2K
Ω
resistance min.
Humidification analog output accuracy: ± 3% typical
Wire gauge 18 gauge maximum, 22 gauge recommended
Dimensions: 4.94”
x 3.38” x 1.13”
Approximate shipping weight: 0.75 lb ( 0.34 kg )
Agency Approvals all models:
UL:
UL 873 (US) and CSA C22.2 No. 24 (Canada), File E27734 with
CCN XAPX (US) and XAPX7 (Canada)
Industry Canada:
ICES-003 (Canada)
Agency Approvals all models
FCC:
Compliant to CFR 47, Part 15, Subpart B, Class A (US)
CE:
EMC Directive 89/336/EEC (Europe Union)
C-Tick:
AS/NZS CISPR 22 Compliant (Australia / New Zealand)
Supplier Code Number N10696
Agency Approvals Wireless models
FCC:
Compliant to: Part 15, Subpart C
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Drawing & dimensions
Vykon and WEEE
The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the European Union (EU) and Norway.
Electric/Electronic devices are labeled in accordance with European Directive 2002/96/EC concerning waste electrical and electronic
equipment (WEEE). The Directive determines the framework for the return and recycling of used Electric/Electronic devices at the end of
life within and throughout the European Union (EU). This label is applied to various products to indicate the product is not to be thrown
away, but rather be reclaimed upon the end of the products useful life per this directive.
Users of electric and electronic equipment with the WEEE marking per annex IV of the WEEE Directive must not dispose of end of life
Electric/Electronic waste as unsorted municipal waste, but rather use the collection framework available to them for the return, recycle and
recovery of WEEE and minimize the environmental impact of Electric/Electronic waste due to the presence of hazardous substance.
FoFig.13 – Thermostat dimensions
Содержание VT7607B5x28(X)
Страница 2: ...2...
