Vulcan-Hart GR Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 56

background image

COMPUTER CONTROL - OLDER

CONTROLS

Operation

Refer to Installation & Operations manual for specific
operating instructions.

Service Programming

The computer control's Service Programming mode is
used to perform system diagnostic tests or to edit
program items that affect the fryer's operation.

NOTE:

If a product key is active (timing), Service

Programming cannot be entered.

Error Messages

For information on computer control error messages,
refer to COMPUTER CONTROL under
TROUBLESHOOTING.

Enter Service Mode

1.

Press V key, and enter password (default: 1972).
Use product key numbers (1 though 0) to enter
values.

A.

"SERVICE" is displayed in the left window,
and the LED lamps above the product keys
1, 2, 4, 5, 6, 7, and 8 come on.

B.

Beeper chirps on each successful key
press. If a key is not pressed within 2
minutes, the computer will automatically exit
Service Programming (except in diagnostic
mode).

2.

To exit a Program item after making a selection,
press V to accept and return to Service
Programming.

3.

To exit Service Programming and return to
operation mode, press V key twice.

Program Item

Key Sequence

LED Status

ON

OFF

Left

Right

Temperature

Offset

•

Press 1 to view offset temperature. To
edit, enter the desired offset temperature
(range 0 to 20°F).

•

Press V to accept selection.

all

OFF

00

F

DEGREES

•

Press Toggle key to select the direction of
the temperature offset (positive or
negative).

POSITIVE OR

NEGATIVE

DEGREES

Melt Cycle On/

Off Times

•

Press 2 and set melt cycle on time.

all

MLTON:

02

MELT ON

•

Press Left or Right Timer arrow key and
set melt off time.

MLTOFF:

13

MELT OFF

Diagnostic

Mode

•

Press 5 to enter diagnostic mode (outputs
for heat, basket lifts, and cooking timers
turned off).

5, 7

DIAGNOST

DIAGNOST

•

Press 1 to toggle left basket lift output; left
basket lift lowers. LED toggles on/off.

5, 7

L BASKET

L BASKET

•

Press 2 to toggle right basket lift output;
right basket lift lowers. LED toggles on/off.

5, 7

R BASKET

R BASKET

•

Press and hold 3 to temporarily activate
heat demand (heat on); release to
deactivate heat demand (heat off). LED
toggles on/off.

5, 7

HEAT DEM

HEAT DEM

•

Press 5 to test drain valve interlock.
Change valve position (open/close) and
press 5 again to update display.

5, 7

Drain valve closed.

5, 7

DRN ON

DRN ON

Drain valve open.

7

5

DRN OFF

DRN OFF

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - SERVICE PROCEDURES AND

ADJUSTMENTS

Page 29 of

56

F35660

Rev. A (0717)

«
...
27
28
29
30
31
...
»

Содержание GR Series

























































Отзывы:

Нет отзывов

Похожие инструкции для GR Series

Бренд: Jata Страницы: 12

Bear Power Pro Series

Бренд: B-Air Страницы: 5

Бренд: Kambrook Страницы: 6

Бренд: KAI Страницы: 13

Бренд: Alliance Laundry Systems Страницы: 88

Бренд: emerio Страницы: 40

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 128

Бренд: GE Страницы: 16

Бренд: DryMax Страницы: 12

Бренд: Sanyo Страницы: 10

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 14

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды