Vulcan-Hart GR Series Скачать руководство пользователя страница 28

Страница: 28 / 56

Press V key to enter Program Mode.

If the Parameter Lock feature is disabled,
Program Mode entry is immediate. If the
Parameter Lock feature is enabled "LoC"
will be displayed.

Use the following key sequence (password)
to enter Program Mode: Left basket/up; Left
basket/up; Right basket/down; Right
basket/down.

Fig. 49

NOTE:

If the proper key sequence is not entered

within 6 seconds, the controller exits Program Mode.

Beeper chirps on each successful key press. If a
key is not pressed within 2 minutes, the control
will automatically exit programming.

To scroll through each of the Program items,
press V and release.

To exit Program Mode at any time, press V and
hold for 1 second.

Program Item

Key Sequence

Display

Left Timer

•

Press Left Basket to increase, or Right Basket to
decrease cook time.

LED above left basket is on.

15:00

time value with flashing colon

(MM:SS).

Right Timer

•

Press Left Basket to increase, or Right Basket to
decrease cook time.

LED above right basket is on.

15:00

time value with flashing colon

(MM:SS).

Set Point

Temperature

•

Press Left Basket to increase, or Right Basket to
decrease set point temperature.

340F

or 171C

Current set point with flashing F or C.

Calibration

Offset

•

Press Left Basket to increase, or Right Basket to
decrease offset temperature (range -20 to +20).

00F

or -00F

Always in °F.

Melt Options

•

Press Left Basket or Right Basket to scroll through
Melt Options.

CY L = Liquid.

CY S = Solid.

CY 0 = No.

Energy Source

•

Press Left Basket or Right Basket to select the
fryer's energy source, electric or gas heat.

ELEC

or gAS

Parameter

Lock

•

Press Left Basket or Right Basket to select desired
Parameter Lock condition.

Uloc

or LoC

Selected parameter is enabled if

flashing.

Degrees F or C

•

Press Left Basket or Right Basket to select desired
Temperature scale.

F or C

NOTES:

Time will change in 1-second increments, accelerating if the button is held.

Temperature will change in 1-degree increments, accelerating if the button is held.

Selecting Parameter Lock enabled will take effect on the next Program Mode entry.

Default value shown in bold.

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - SERVICE PROCEDURES AND

ADJUSTMENTS

F35660

Rev. A (0717)

Page 28 of

Содержание GR Series

























































Результаты поиска

Содержание GR Series

Отзывы:

Похожие инструкции для GR Series

Бренды по названию

Популярные бренды

Vulcan-Hart GR Series, Руководство по обслуживанию

Результаты поиска

Содержание GR Series

Отзывы:

Похожие инструкции для GR Series

Бренды по названию

Популярные бренды