Vulcan-Hart GR Series Скачать руководство пользователя страница 15

Страница: 15 / 56

CAUTION

If orifice is clogged with debris, clean with

air or liquid only.

Fig. 20

Reverse procedure to install, and then check for
proper operation.

TEMPERATURE PROBE

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Shut off the gas

before servicing the unit and follow
lockout / tagout procedures.

CAUTION

Do not sharply bend and kink the

temperature probe, or damage may occur.

Drain shortening from fryer tank.

Disconnect temperature probe and drain valve
interlock (DVI) connector.

Fig. 21

NOTE:

The connector has six pin positions, and is

labeled G on the wiring diagram.

Remove the temperature probe lead wires from
the 6-pin female connector.

Pin No.

Description

G-1

Probe

G-2

Empty

G-3

Probe

G-4

Empty

G-5

DVI Switch (24VAC) N.O.

G-6

DVI Switch (24VAC)

OUT

Remove the burners as outlined under GAS
BURNERS.

Remove the probe retaining and packing nuts.

Fig. 22

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - REMOVAL AND REPLACEMENT

OF PARTS

Page 15 of

F35660

Rev. A (0717)

Содержание GR Series

























































Результаты поиска

Содержание GR Series

Отзывы:

Похожие инструкции для GR Series

Бренды по названию

Популярные бренды

Vulcan-Hart GR Series, Руководство по обслуживанию

Результаты поиска

Содержание GR Series

Отзывы:

Похожие инструкции для GR Series

Бренды по названию

Популярные бренды