Vulcan-Hart GR Series Скачать руководство пользователя страница 13

Страница: 13 / 56

Fig. 15

Reverse procedure to install.

GAS ORIFICE

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Shut off the gas

before servicing the unit and follow
lockout / tagout procedures.

Remove gas orifice spud from orifice extension.

NOTE:

The spud screws into the orifice extension.

When installing, do not overtighten the spud, or
damage to the threads may occur.

Fig. 16

Reverse procedure to install.

GAS COMBINATION VALVE

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Shut off the gas

before servicing the unit and follow
lockout / tagout procedures.

All gas joints disturbed during

servicing must be checked for leaks. Check with a
soap and water solution (bubbles). Do not use an open
flame.

NOTE:

If a gas combination valve is malfunctioning,

do not attempt to disassemble the valve for repair.
Install a replacement gas combination valve.

Remove burners as outlined in GAS
BURNERS.

Disconnect lead wires from gas combination
valve.

On fryers with gas valve arm extension only,
remove cotter pin securing handle to gas valve
on/off knob adaptor, and pull handle away from
valve assembly.

Disconnect pilot tube from has combination
valve.

Disconnect gas line fittings, then remove gas
combination valve.

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - REMOVAL AND REPLACEMENT

OF PARTS

Page 13 of

F35660

Rev. A (0717)

Содержание GR Series

























































Результаты поиска

Содержание GR Series

Отзывы:

Похожие инструкции для GR Series

Бренды по названию

Популярные бренды

Vulcan-Hart GR Series, Руководство по обслуживанию

Результаты поиска

Содержание GR Series

Отзывы:

Похожие инструкции для GR Series

Бренды по названию

Популярные бренды