Vulcan-Hart GR Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 56

background image

Fig. 26

7.

Reverse procedure to install.

POWER SUPPLY BOX

COMPONENTS

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Shut off the gas

before servicing the unit and follow
lockout / tagout procedures.

All gas joints disturbed during

servicing must be checked for leaks. Check with a
soap and water solution (bubbles). Do not use an open
flame.

NOTE:

The power supply box must be removed to

access the following components: ignition control
module, transformer, R1 pump motor relay, and R2 fill
relay.

1.

Remove burners as outlined under GAS
BURNERS.

2.

Remove wire tie, and disconnect ignitor cable
from ignitor/flame sense electrode on the gas
pilot.

Fig. 27

NOTE:

When installing, replace wire tie to secure

ignitor cable.

3.

Remove lower basket lift cover as outlined under
COVERS AND PANELS.

4.

Disconnect all wiring harness connectors and
power cords from power supply box.

5.

Remove screw securing power supply box to
mounting bracket.

Fig. 28

NOTE:

Power supply box is slotted at the rear, and

secured by a hanging bracket (loose fit).

6.

Remove cover from power supply box.

Fig. 29

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - REMOVAL AND REPLACEMENT

OF PARTS

Page 17 of

56

F35660

Rev. A (0717)

«
...
15
16
17
18
19
...
»

Содержание GR Series

























































Отзывы:

Нет отзывов

Похожие инструкции для GR Series

Бренд: Morphy Richards Страницы: 8

Бренд: Mirta Страницы: 36

Professional 1 Slim

Бренд: Taurus Страницы: 68

Бренд: TEAM CUISINE Страницы: 17

Бренд: Flame Страницы: 2

Бренд: Mesko Страницы: 67

Бренд: LG Страницы: 108

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 64

Бренд: Siemens Страницы: 68

Бренд: Siemens Страницы: 64

Бренд: Campomatic Страницы: 23

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 7

Бренд: Whirlpool Страницы: 9

Бренд: Whirlpool Страницы: 6

Бренд: Whirlpool Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды