Volvo Penta D34A MS Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 89

background image

41

Maintenance: Engine

Engine

Valve clearance

Check and adjust the valve clearance on a cold engine. The valves are adjusted when the piston is at top dead
center of compression stroke. The valve bridge is adjusted first, and then the clearance of the rocker arm.

IMPORTANT! The engine must under no circumstances be running when checking and adjusting the

valve clearance since the valves can knock against the pistons and cause serious damage.

IMPORTANT! Make sure that the stop lever is pulled out and the starter key switched off.

Top dead center on compression stroke

1. Turn the engine in the normal direction to align

the timing mark [1 .6] on the damper with the
pointer as shown.

2. Remove the rocker cover of the cylinder on which

the valve clearance is to be checked and adjus-
ted, and make sure the inlet and exhaust valves
have some clearance. If the timing mark [1 .6] is
aligned with the pointer, either the No. 1 or No. 6
piston is at top dead center on the compression
stroke.

Adjust the valve bridge

IMPORTANT! Make sure the clearance

between the valve bridge and valve rotator is 1.5
mm [0.059 in.] or more if not, interference will
occur between the bridge and rotator to cause
the valve cones to get out of place. If the
clearance is less than 1.5 mm [0.059 in.] after
the height of valves has been adjusted, consult
your dealer.

NOTE! Before inspecting the valve clearance, adjust
the height of the two valves. Bring the bridge into con-
tact with the valves, by means of the valve-bridge ad-
justing screw, so that there is no difference in height
between the two valves. If the valve seats are worn,
one valve will differ from another in height, increasing
the clearance between the valve stem and bridge,
leading to an increased valve clearance.

1. Unscrew the lock nut and adjusting screw on the

pair of valves on the cylinder so that there is clea-
rance between the yoke and the valve stem.

2. Press the valve yoke down.Turn the adjusting

screw so that it makes contact with the valve
stem.

3. Turn an additional 10 degrees. Lock the adjusting

screw with the lock nut.

NOTE! Check if the bridge is properly adjusted, by
putting a little drop of oil the valve stem top.

Plus d'informations sur : www.dbmoteurs.fr

«
...
39
40
41
42
43
...
»

Содержание D34A MS


























































































Отзывы:

Нет отзывов

Похожие инструкции для D34A MS

Бренд: W&H Страницы: 42

Бренд: Perkins Страницы: 92

Motorcycle Accessories

Бренд: S&S Cycle Страницы: 20

Бренд: Avco Lycoming Страницы: 106

Бренд: Perkins Страницы: 108

Бренд: GR Страницы: 8

SW Brushless Series

Бренд: Swiwin Страницы: 14

Бренд: Kohler Страницы: 108

Бренд: Honda Страницы: 2

Бренд: O.S. engine Страницы: 4

O.S. Max-160FXRing

Бренд: O.S. engine Страницы: 10

Бренд: Wood-mizer Страницы: 80

Бренд: Tanaka Страницы: 17

Бренд: mycom Страницы: 51

DuraForce HMR Series

Бренд: Eaton Страницы: 24

Бренд: Hatz Diesel Страницы: 129

Бренд: Tecumseh Страницы: 24

Бренд: E-FLITE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды