Volvo Penta D34A MS Скачать руководство пользователя страница 66

Страница: 66 / 89

Maintenance: Freshwater system

5. Close air vents. Check the coolant level and top

up if needed.

IMPORTANT! Make sure that the engine is

filled with lubrication oil before starting or
cranking the engine.

IMPORTANT! The engine must not be

started before the system has been bled and
topped up.

6. Start the engine and run it under light load until the

thermostat valve opening temperature is reached.

7. Check air vents for leaks.

8. Stop the engine and allow it to cool. Check the

coolant level in the expansion tank and top up if
needed.

Draining the coolant

1. Remove the filler cap on the expansion tank.

2. Open the air vent cocks and then drain the coo-

lant from the drain cocks.

IMPORTANT! Check that the coolant really

drains. Deposits may need to be removed from
inside the drain plugs/taps.

3. Drain all systems connected to the freshwater

system, e.g. heater, water heater, etc.

4. Close all drainage points.

Flushing the freshwater system

The system should be flushed before changing coo-
lant to avoid inferior cooling performance due to depo-
sits in the cooling system.

1. Drain the coolant as described earlier.

2. Insert a hose into the filler opening and flush with

fresh water.

3. Flush until the water running out of the drainage

points is clean.

4. Close all drainage points when the flushing water

has run out.

5. Fill with coolant. See section coolant filling when

empty.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D34A MS


























































































Результаты поиска

Содержание D34A MS

Отзывы:

Похожие инструкции для D34A MS

Бренды по названию

Популярные бренды

Volvo Penta D34A MS, Руководство оператора

Результаты поиска

Содержание D34A MS

Отзывы:

Похожие инструкции для D34A MS

Бренды по названию

Популярные бренды