Volvo Penta D34A MS Скачать руководство пользователя страница 69

Страница: 69 / 89

Maintenance: Electrical system

Electrical system

Protective devices inspection

Make sure that the instruments and the alarm func-
tions of the engine control system work properly.

Checking the electrical wiring

Check for loose or damaged electrical cables.
Damaged cables must be replaced.

Starter motor inspection

1. Visually inspect the starter motors for damages

and dirt build-up. Repair and clean if needed.

2. Check the pinion for shifting and meshing action.

If the starters has a defect, consult your dealer.

3. Check if the clutch of the starter motors operates

smoothly.

Alternator inspection

1. Inspect the alternator on functionality and clean it

if needed.

2. Remove the V-belt from the alternator. Turn the

alternator pulley by hand to check the rotation. If
the alternator has a defect, consult your dealer.

Checking/Adjusting/Changing the
drive belts

WARNING! Stop the engine before

commencing maintenance work.

Check belt tension and condition regularly. If the belt
is too tight it can damage bearings and if it is too loo-
se it may slip. Check and adjust after operation when
the belt is warm.

The belt is correctly tensioned when it can be depres-
sed approximately 10 mm between the pulleys. Clean
the belt grooves before fitting a new belt.

IMPORTANT! Always change a belt that

appears worn or is cracked (belts working in
pairs must be replaced together).

IMPORTANT! Always keep the belts clear of

oil or grease. Oil or grease can cause the
belts to slip, which might shorten belt life.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D34A MS


























































































Результаты поиска

Содержание D34A MS

Отзывы:

Похожие инструкции для D34A MS

Бренды по названию

Популярные бренды

Volvo Penta D34A MS, Руководство оператора

Результаты поиска

Содержание D34A MS

Отзывы:

Похожие инструкции для D34A MS

Бренды по названию

Популярные бренды