Volvo Penta D34A MS Скачать руководство пользователя страница 46

Страница: 46 / 89

Maintenance: Lubrication system

Changing oil filter

Each pair of filters has its own shut off valve located on the housing between the filters. The oil filters can be
changed while the engine is running as the oil flow can be directed through two filters at a time.

WARNING! Always keep all four filters in operation under norlmal operating conditions.

WARNING! Reduce the engine speed to idle when changing oil filters on a running engine.

5. Mount the new filter by hand until the gasket is in

contact with the sealing surface. Then tighten the
filter a further approximately 3/4 of a turn.

6. Put the filter on-line by turning the valve in posi-

tion A.

7. Replace the left filters as above. Position B is the

left filters change position.

8. Replace all four full-flow filters at the same time.

NOTE! After a lubrication oil filter change, open the fil-
ter and check for metal parts.

1. Remove the cover from the filter switch valve by

disconnecting the two bolts.

WARNING! Working on or approaching a running

engine is a safety hazard. Beware of rotating
parts and hot surfaces.

2. Cut off the oil flow through the right filters by tur-

ning the setting valve in position C.

3. Unscrew the oil filter using the special tool. Dis-

card the filter.

NOTE! Place a drip pan beneath the filter when
removing to avoid oil spill.

4. Lightly oil the new filter’s rubber gasket and check

its mating surface on the mounting.

A: Normal running (all filters connected).

B: Left filters can be changed.

C: Right filters can be changed.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D34A MS


























































































Результаты поиска

Содержание D34A MS

Отзывы:

Похожие инструкции для D34A MS

Бренды по названию

Популярные бренды

Volvo Penta D34A MS, Руководство оператора

Результаты поиска

Содержание D34A MS

Отзывы:

Похожие инструкции для D34A MS

Бренды по названию

Популярные бренды