Volvo Penta D34A MS Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 89

background image

17

General

Before starting a new or reconditioned engine for the first time, give it an initial inspection. This to guarantee your
own safety as well as the maximum service life of the engine.

New engine initial service

External inspection

1. Check the engine control system for loose termin-

als.

2. Check defects of engine parts.

3. Check the following components for loose bolts or

nuts:

* Plugs and covers of fuel, lubrication and cooling

system

* Coupling of fuel injection pump and shaft

* Crankshaft pulley and vibration damper

* Mounting brackets

* Fuel control linkage

* Turbocharger

* Timing gear case

* Exhaust manifolds

* Cylinder heads

* Air-duct connection-hose clamp

4. Check for fuel, oil, coolant and air leaks and repair

if needed.

5. Make commissioning report for new or overhauled

engine.

IMPORTANT! All covers must be mounted before

attempting to start your engine.

Valves and plugs

Make sure the following valves and plugs are open or
closed properly:

Fuel supply valve

Open

Coolant drain cock (engine)

Closed

Coolant drain cock (water pump)

Closed

Coolant drain cock (heat exchanger) Closed

IMPORTANT! If the coolant drain cocks are not

closed the coolant will drain from the engine and
this may cause severe damage to the engine.

Electrical wiring

Check for loose or damaged electrical wiring around
the engine and if necessary firmly reconnect to ter-
minals or cable-joint portions. Damaged cables must
be replaced.

If your engine is reconditioned, make sure the wiring
is according to the drawings.

Filling the fuel system

Refer to chapter ”Maintenance: Fuel system”.

Filling the lubrication system

Refer to chapter ”Maintenance: Lubrication system”.

Filling the cooling system

Refer to chapter ”Maintenance: Cooling system”.

Plus d'informations sur : www.dbmoteurs.fr

«
...
15
16
17
18
19
...
»

Содержание D34A MS


























































































Отзывы:

Нет отзывов

Похожие инструкции для D34A MS

Бренд: Eaton Страницы: 32

Бренд: VEM Страницы: 35

Бренд: nord Страницы: 12

Бренд: Superrollo Страницы: 68

Бренд: Key Automation Страницы: 50

Бренд: Siemens Страницы: 28

6FB1203-5AT00-7MP0

Бренд: Siemens Страницы: 7

COMBIMASTER CM110/3

Бренд: Siemens Страницы: 21

Бренд: Siemens Страницы: 19

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 38

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 40

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды