Volvo Penta D34A MS Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 89

background image

19

Non-classifiable control system

Instrument panels

Instrumentation for the main control position and auxi-
liary control position.

1. Temperature gauge. Indicates the engine coolant

temperature.

2. Oil pressure gauge. Indicates the pressure of the

engine lubricant.

3. Voltmeter. Indicates the charge voltage from the

generator when the engine is running and the bat-
tery voltage when the engine is stopped.

4. Tachometer. Indicates the speed of the engine in

rpm.

5. Hour counter. Shows the total number of engine

running hours as a decimal number.

6. Press button for testing and acknowledging

alarms (see next page “Warning displays”).

7. Siren for acoustic alarm that sounds if one of the

warning lamps comes on.

8. Warning display (see section “Warning displays”,

pos 1–3).

9. Starting switch (see next page).

10. Press button for instrument illumination.

This chapter describes the non-classifiable control system which is available for your engine. Note that that tacho-
meter, oil gauge, temperature gauge, charge gauge, starting switch, etc., that are shown here as panel mounted,
in some cases may be mounted separately.

If the vessel is equipped with instruments not described here and you are not sure of their function, please get in
touch with the shipyard or the company that installed the installation aboard the vessel.

IMPORTANT! Read the chapter “Starting” before starting your engine.

11. Oil pressure gauge. Indicates the oil pressure in

the reverse gear.

12. Charge air pressure gauge. Indicates the turbo-

charger boost pressure.

Plus d'informations sur : www.dbmoteurs.fr

«
...
17
18
19
20
21
...
»

Содержание D34A MS


























































































Отзывы:

Нет отзывов

Похожие инструкции для D34A MS

Бренд: Painless Performance Страницы: 24

Бренд: Jacobsen Страницы: 103

Command PRO EFI PCV850

Бренд: Kohler Страницы: 10

Бренд: Mercedes-Benz Страницы: 940

Бренд: Vanguard Страницы: 120

Бренд: Kohler Страницы: 109

Бренд: Tanaka Страницы: 7

Бренд: BGS technic Страницы: 8

Бренд: aFe Power Страницы: 16

Бренд: Panther Страницы: 7

Metaphaser MP-LE1007

Бренд: Metaphase Technologies Страницы: 35

Бренд: Honda Страницы: 40

Бренд: Honda Страницы: 42

Бренд: New Holland Страницы: 41

Бренд: Honda Страницы: 5

Бренд: Honda Страницы: 60

Бренд: DLE Страницы: 4

MINIMAX 3TNM72-GGE

Бренд: Yanmar Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды