Volvo Penta D34A MS Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 89

background image

63

Maintenance: Cooling system, general

1.

2.

3.

3.

4.

5.

6.

5.

6.

7.

7.

8.

9.

10.

1. Rawwater inlet

2. Rawwater pump (optional)

3. Charge air cooler

4. Freshwater pump

5. Lubrication oil cooler

6. Engine

7. Thermostat valve

8. Heat exchanger

9. Expansion tank

10. Rawwater outlet

Cooling system D34A MT HE

The thermostat regulated freshwater system is cooling the engine and the lubrication oil cooler. An engine driven
cooling water pump circulates the coolant through the heat exchanger and through the engine.

The rawwater system is cooling the charge air and the coolant in the freshwater cooling system. The rawwater cir-
cuit is designed for seawater cooling or for connection to a central cooling system.

Freshwater circuit
Rawwater circuit

Freshwater drain points (D)

D

D

D

D

Plus d'informations sur : www.dbmoteurs.fr

«
...
61
62
63
64
65
...
»

Содержание D34A MS


























































































Отзывы:

Нет отзывов

Похожие инструкции для D34A MS

Бренд: O.S. engine Страницы: 32

Бренд: Saab Страницы: 30

Бренд: E-MAG Страницы: 30

Бренд: Globe Страницы: 11

Бренд: Lenze Страницы: 20

2-10-4 TEXAS STEAM ENGINE

Бренд: Premier Страницы: 24

Бренд: Saito Страницы: 27

PNEUTORQUE PT 1

Бренд: norbar Страницы: 11

Бренд: Brother Страницы: 76

Бренд: Brother Страницы: 112

Бренд: Brother Страницы: 22

Бренд: Volkswagen Страницы: 64

ZAtop SM180.24/B

Бренд: ZIEHL-ABEGG Страницы: 16

Бренд: NEUGART Страницы: 2

Бренд: NEUGART Страницы: 2

Бренд: Volvo Penta Страницы: 96

Бренд: Lycoming Страницы: 74

Бренд: Robin America Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды