background image

It  is  of  vital  importance,  before  attempting  to 
operate  your  engine,    to  read  the  general 
'SAFETY  INSTRUCTIONS  AND  WARNINGS' 
section  on  pages  2-4  of  this  booklet  and  to 
strictly adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction  manual,  so  as  to  familiarize 
yourself with the controls and other features of 
the engine.
Keep these instructions in a safe place so that 
you  may  readily  refer  to  them  whenever 
necessary.
It is suggested that any instructions supplied 
with the aircraft, radio control equipment, etc., 
are accessible for checking at the same time.

−1− 

2-4 

 

 

7-8 

9-10 

 

10-11 

 

12 

 

15 

16 

17 

 

 

18

 

14 

 

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

INTRODUCTION, BEFORE INSTALLING THE ENGINE
BASIC ENGINE PARTS

INSTALLATION OF THE ENGINE,
THROTTLE LINKAGE

INSTALLATION OF SILENCER (MUFFLER)
FUEL TANK LOCATION

GLOWPLUGS, FUEL

PROPELLER, MIXTURE CONTROLS

STARTING

RUNNING-IN ("Breaking-in")

MIXTURE CONTROL ADJUSTMENT CHART

CONTENTS

SUBSEQUENT READJUSTMENT,
CARBURETOR CLEANLINESS.
ENGINE CARE AND MAINTENANCE
VALVE  ADJUSTING

O.S. GENUINE PARTS & ACCESSORIES

ENGINE EXPLODED VIEW 

ENGINE PARTS LISTS

CARBURETOR EXPLODED VIEWS &
PARTS LIST, THREE VIEW DRAWING

MIXTURE CONTROL VALVE ADJUSTMENT,
REALIGNMENT OF MIXTURE CONTROL VALVE,
SUBSEQUENT STARTING PROCEDURE

13 

 

Содержание O.S. Max-160FXRing











Отзывы: