Volvo Penta 22 Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 66

background image

40

Fuel pre-filter. Replacement

Fuel pre-filters and water separators are accessories
and are available in two variants.

Filter insert replacement

Close fuel cock at the fuel tank. Position a container
under the fuel filter. Remember to dispose of the old
filter at a proper disposal site.

Fuel pre-filter type A:

Remove the glass bowl by

slackening off screw (2). Empty and clean glass.
Replace insert and reinstall glass. Open fuel cock.
Undo the screw (3) a few turns and the glass will fill
with fuel. Bleed fuel system.

Fuel pre-filter type B:

Remove cover (2) and lift up

the insert. Drain water and contaminants through the
drain cock (1). Install new filter insert and fill container
with clean diesel oil. Screw on cover and tighten by
hand. Open fuel cock. Bleed fuel system.

WARNING!

Approaching or working on a running

engine is dangerous. Watch out for rotating
components and hot surfaces.

IMPORTANT!

Start the engine and check for

leaks.

2

3

1

A

B

1

2

7738666 - Downloaded from www.volvopenta.com 31/05/2007 12:43:18

«
...
38
39
40
41
42
...
»

Содержание 22 Series



































































Отзывы:

Нет отзывов

Похожие инструкции для 22 Series

Бренд: LaserPerformance Страницы: 11

Бренд: LaserPerformance Страницы: 16

Бренд: 3d Страницы: 17

FLEXIBLE FURLER 2

Бренд: CDI Страницы: 18

Бренд: Cobalt Digital Inc Страницы: 140

Бренд: grabner Страницы: 24

Бренд: Four winns Страницы: 139

Бренд: Four winns Страницы: 79

Бренд: Highfield Страницы: 29

Бренд: Malibu Boats Страницы: 76

Бренд: Alliaura Marine Страницы: 44

Бренд: Zodiac Страницы: 18

CADET 200 Roll Up

Бренд: Zodiac Страницы: 12

Бренд: Brunswick Страницы: 148

Бренд: Yamaha Страницы: 214

Бренд: Ventus Страницы: 54

Бренд: Sea Eagle Boats Страницы: 15

Fishing Explorer 350fx

Бренд: Sea Eagle Boats Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды