Volvo Penta 22 Series Скачать руководство пользователя страница 62

Страница: 62 / 66

Engine

Engine designation ..........................................

MD22L-B, MD22P-B, TMD22-B, TMD22P-C, TAMD22P-B

No. of cylinders ...............................................

Cylinder bore/stroke ........................................

84.5/88.9 mm

Cylinder volume ...............................................

2 liters

Max. bhp ..........................................................

See sales literature

Idling speed .....................................................

800 ± 25 rpm

Wide Open Throttle (WOT) range ...................

See chapter ”Operation”

Injection order ..................................................

1-3-4-2

Rotational direction, viewed from in front .............

Clockwise

Max. permitted rake backwards (while running)

20°

Max. list (while running) ..................................

30°

Valve clearances cold engine: Intake .............

0.20-0.40 mm (adjustment play=0.25-0.35 mm)

Valve clearances cold engine: Exhaust .........

0.30-0.50 mm (adjustment play=0.35-0.45 mm)

Weight of engine without water and oil ...........

MD22L=220kg, MD22P=223kg, TMD22=225kg, TAMD22=235kg

Cooling system

Freshwater coolant system capacity ..............

7,5 liters

Thermostat: Starts opening at ........................

81°C ± 4°C

Thermostat: Fully open at ...............................

95°C ± 3°C

Electrical system

System voltage ...............................................

12 V

Starter battery (capacity) ................................

70 Ah

AC generator ....................................................

14V/60A

Lubricating oil recommendations

Oil volume (including oil filter) .........................

6.0 liters

Oil quality according to

API* ...........................................................

CD, CF, CF–4, CG–4

ACEA* .......................................................

E1, E2, E3

VDS* ..........................................................

VDS, VDS–2

Viscosity is selected from the table** ............

* API= American Petroleum Institute, ACEA= Association des Constructeurs Européenne d’Automobiles, VDS=Volvo Drain Specification
** Temperature based on constant outside air temperature.

Technical data

Fuel specification

Fuel must meet national and international standards at least. For example:

EN 590

(with national environmental and cold standards)

ASTM D 975 No 1-D and 2-D
JIS KK 2204

Sulphur content:

According to statutory requirements.

Fuels with extremely low sulphur contents (“urban diesel” in Sweden and “city diesel” in Finland) can cause a drop in

output of 5% and an increase in fuel consumption of 2-3%.

7738666 - Downloaded from www.volvopenta.com 31/05/2007 12:43:18

Содержание 22 Series



































































Результаты поиска

Содержание 22 Series

Отзывы:

Похожие инструкции для 22 Series

Бренды по названию

Популярные бренды

Volvo Penta 22 Series, Инструкция

Результаты поиска

Содержание 22 Series

Отзывы:

Похожие инструкции для 22 Series

Бренды по названию

Популярные бренды