Volvo Penta 22 Series Скачать руководство пользователя | Manualshive

Страница: 16 / 66

background image

16

Controls

This chapter only describes the controls available from Volvo Penta as standard alternatives for your engine. If
your boat is equipped with controls which are not described here and you feel uncertain about the functions,
contact your Volvo Penta dealership.

Top mounting controls

Side mounting controls

Maneuvering

Shifting and engine speed are controlled with the same lever (1).

N

= Neutral position. Drive/reverse gear disengaged.

F

= Drive/reverse gear engaged for movement ahead.

R

= Drive/reverse gear engaged for movement astern.

T

= Engine speed control

A neutral position switch is available as an accessory, this will only
permit the engine to be started with the drive/reverse gear
disengaged.

Friction brake

The friction brake only affects the engine speed control
movements.

1. Lift the cover over the control. For side-mounted controls the

lever must first be removed.

2. Set the lever to the half-open throttle/reverse position.

3. Adjust the friction brake. Turning the screw clockwise (

+

) makes

the lever movement stiffer, while turning counterclockwise (

–

)

makes it easier to move the lever.

4. Reinstall the cover and lever.

Disengaging the shift function

Move lever (1) to the neutral position (N). Press in button (2), move
the lever slightly forward and release the button. The shift function
is now disengaged and the lever affects only engine speed.

When the lever is moved back to the neutral position it will
automatically re-engage.

IMPORTANT!

Take care not to engage the drive/reverse gear

by mistake.

T

T

1

2

T

T

2

1

7738666 - Downloaded from www.volvopenta.com 31/05/2007 12:43:18

«
...
14
15
16
17
18
...
»

Содержание 22 Series



































































Отзывы:

Нет отзывов

Похожие инструкции для 22 Series

Бренд: NorthStar Страницы: 2

Бренд: Bayliner Страницы: 80

Бренд: Cobalt Digital Inc Страницы: 122

GTX 4-TEC 5573 2002

Бренд: Sea-doo Страницы: 505

2008 2008 70141

Бренд: CORRECT CRAFT Страницы: 188

Бренд: Polaris Страницы: 114

Бренд: Trophy Страницы: 112

Бренд: Old Town Canoe Co. Страницы: 14

WaveRunner SuperJet 700 2001

Бренд: Yamaha Страницы: 107

Бренд: Feathercraft Страницы: 2

BACKWOODS ANGLER 75

Бренд: Aquaglide Страницы: 28

Бренд: Scout Boats Страницы: 120

Бренд: Scout Boats Страницы: 135

Бренд: Scout Boats Страницы: 148

Бренд: Scout Boats Страницы: 150

Бренд: Scout Boats Страницы: 161

Бренд: Scout Boats Страницы: 166

Бренд: Scout Boats Страницы: 171

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды