Volvo Penta 22 Series Скачать руководство пользователя

Страница: 27 / 66

Maintenance schedule

Your Volvo Penta engine and its equipment is designed for maximum service life and reliability. They are built to
survive in a tough marine environment, but also to cause as little environmental impact as possible. Regular
maintenance according to the following schedule is necessary if the engine and transmission are to operate
without problems.

WARNING!

Read the chapter on Maintenance carefully before starting work. It contains instructions on how

to carry out the work safely and correctly.

IMPORTANT!

Service operations marked

must be carried out by an authorized Volvo Penta Service

workshop.

DAILY BEFORE STARTING FOR FIRST TIME

●

Engine oil. Checking level .............................................................................. page 31

●

Coolant. Checking level ................................................................................. page 33

EVERY 14 DAYS

●

Fuel filter. Drain water .................................................................................... page 39

●

Fuel pre-filter. Drain water .............................................................................. page 39

●

Generator and circulation pump drive belts. Check ........................................ page 30

●

Servo pump drive belt (SX). Check ................................................................ page 30

●

Servo pump (SX). Check oil level .................................................................. page 29

●

Seawater filter. Cleaning ................................................................................ page 37

●

Battery. Check electrolyte level ..................................................................... page 42

●

Reverse gear. Check oil level ................................................................... page 47–48

●

S-drive. Check oil level .................................................................................. page 47

●

SX-drive. Check corrosion protection ............................................................. page 52

●

SX-drive. Check oil level in trim pump ........................................................... page 54

AFTER THE FIRST 20–50 OPERATING HOURS

First Service inspection .......................................................................... not shown

A first Service Inspection must be carried out in accordance with the instructions in the Warranty and

Service Book.

EVERY 100 OPERATING HOURS OR AT LEAST ONCE A YEAR

●

S-drive. Checking/Replacing corrosion protection ........................................... page 49

●

S-drive. Check rubber seal (hull/drive) ............................................................ page 50

●

SX-drive. Checking aluminum anode .............................................................. page 52

●

SX-drive. Oil change ...................................................................................... page 53

●

SX-drive. Grease CV joint and primary shaft bearing ............................... page 56–57

●

SX-drive. Checking CV joint and exhaust bellows. ......................................... page 56

7738666 - Downloaded from www.volvopenta.com 31/05/2007 12:43:18

Содержание 22 Series



































































Результаты поиска

Содержание 22 Series

Отзывы:

Похожие инструкции для 22 Series

Бренды по названию

Популярные бренды

Volvo Penta 22 Series, Инструкция

Результаты поиска

Содержание 22 Series

Отзывы:

Похожие инструкции для 22 Series

Бренды по названию

Популярные бренды