Vmetro M5210RP-EFF Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 130

Vmetro M5210RP-EFF Скачать руководство пользователя страница 51

37

Issued June 20, 2007

M5000 Series: User Guide

Secondary and Tertiary PCI Segments

4.2 Secondary and Tertiary PCI Segments

PCI Mode and Speed Configuration

The PCIXCAP and M66EN pins of a PMC module determine which clock speed and protocol (PCI
vs. PCI-X) can be used on the segment. There are five detectable modes of operation: 33/66MHz
PCI and 66/100/133MHz PCI-X.

Configuration switches can be used to:

•

Ground the PCIXCAP signal to force PCI operations, or pull low to inhibit 100/133 MHz
operations by configuration switches.

•

The M66EN signal can also be grounded through in order to inhibit 66MHz PCI operations.

•

Select between 133 and 100 MHz as the maximum operating frequency.

The detected PCIXCAP/M66EN/dip-switches values determine the frequency of the clock
generator for the segment. Table 2-9 on page 17 for dip-switch settings.

Arbitration

Secondary and Tertiary PCI Segments

The built-in PCI-X arbiter of the PCI6540 PCIX-to-PCIX Bridge is used. The arbiter provides two
REQ/GNT pairs to the PMC to support a dual device PPMC.

IDSEL Assignment

Secondary PCI Segment

•

AD[17] is used for the PMC#1 IDSEL

•

AD[18] is used for the PMC#1 IDSELB

•

AD[19] is used for the PCI6540 P2P Secondary Side IDSEL (PCI6540 located in the Processor
Subsystem)

•

AD[20] is used for the PCI6540 P2P Primary Side IDSEL (PCI6540 located between the
Secondary and Tertiary PCI Segments)

Tertiary PCI Segment

•

AD[17] is used for the PMC#2 IDSEL

•

AD[18] is used for the PMC#2 IDSELB

•

AD[19] is used for the PCI6540 P2P Secondary Side IDSEL (PCI6540 located between the
Secondary and Tertiary PCI Segments)

Note –

Even if PMCs can only signal that they are either 66 or 133 MHz compliant in PCI-X

mode, the host may decide to run 133 MHz capable boards at a lower frequency (typically
100MHz) if the total number of loads is too high for the system to achieve 133MHz
operations.

«
...
49
50
51
52
53
...
»

Содержание M5210RP-EFF



































































































































Отзывы:

Нет отзывов