Vmetro M5210RP-EFF Скачать руководство пользователя страница 27

Страница: 27 / 130

Issued June 20, 2007

M5000 Series: User Guide

Switches and Jumper Settings

Default Jumper and Switch Settings

The factory settings of the jumpers and switches are shown in Table 2-1:

DIP Switch Settings

PCI-X to PCI-X Bridges

•

The PCIX-to-PCIX Bridge #1 is located between the processor subsystem and the rest of the
board. It is configured using the switch SW2.

•

The PCIX-to-PCIX Bridge #2 is located between the two PMC subsystems. It is configured
using the switch SW9.

•

The PCIX-to-PCIX Bridge #3 is located between the second PMC subsystem and the Extension
subsystem. It is configured using the switch SW8.

TABLE 2-1.

Default Jumper and Switch settings

Jumper/switch

Position

Description

JP1

Inserted on left side on R
models. Removed on
others

PCI to RACEway Bridge Reset Configuration

JP2

Removed

ECO SPROM Write Protection

JP3

Removed

Processor Boot SPROM Download

SW1

All OFF

PMC#2 PCI-X Capability Selection

SW2

All ON

PCI-X to PCI-X Bridge Configuration

SW3

1: ON

2, 3, 4: OFF

PCI to VME Bridge Configuration

SW4

All OFF

PMC#1 PCI-X Capability Selection

SW5

All OFF

PCI-to-VME Bridge Configuration

SW6

All OFF

PMC#1 Monarch Selection & Processor SDRAM
ECC Enable/Disable

SW7

1: OFF

2: ON

PCI-to-RACEway Bridge Configuration

SW8

All ON

PCI-X to PCI-X Bridge Configuration

SW9

All ON

PCI-X to PCI-X Bridge Configuration

SW10

1, 5, 6: ON

2, 3, 4: OFF

Processor Subsystem Configuration

SW11

1: ON

2: OFF

PCI to VME Bridge Configuration

Содержание M5210RP-EFF



































































































































Результаты поиска

Содержание M5210RP-EFF

Отзывы:

Vmetro M5210RP-EFF, Руководство пользователя, Страница: 27 / 130

Результаты поиска

Содержание M5210RP-EFF

Отзывы: