Vmetro M5210RP-EFF Скачать руководство пользователя страница 53

Страница: 53 / 130

Issued June 20, 2007

M5000 Series: User Guide

PCI6540 PCIX-to-PCIX Bridge

4.3 PCI6540 PCIX-to-PCIX Bridge

This Bridge has been discussed in “PCI-X to PCI-X Bridges” on page 32. What follows are details
appropriate for this particular bridge.

Power-up / Reset Configuration Options

PCI-X Capability

Both primary and secondary interfaces can be run in PCI or PCI-X modes. See “PCI-X Capability
Selection for PMC Slots” on page 11.

Secondary Port Arbiter Setup

As the only built-in arbiter present on the secondary PCI bus, the PCI6540 internal arbiter is used to
arbitrate.

Primary Interface

The primary interface of this bridge is connected to the secondary interface of the Secondary PCI
Segment bridge and to the first PMC site (PMC#1).

Secondary Interface

The secondary interface of this bridge is connected to the second PMC site (PMC#2) and the
primary interface of another PCI6540 bridge.

Содержание M5210RP-EFF



































































































































Результаты поиска

Содержание M5210RP-EFF

Отзывы:

Vmetro M5210RP-EFF, Руководство пользователя, Страница: 53 / 130

Результаты поиска

Содержание M5210RP-EFF

Отзывы: