Vmetro M5210RP-EFF Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 130

Vmetro M5210RP-EFF Скачать руководство пользователя страница 96

82

M5000 Series: User Guide

Issued June 20, 2007

Universe IID Configuration Examples

VMEbus Register Access Image

In this configuration example, the VMEbus Register Access Image is set up by use of the DIP
switch and jumpers.

With the jumper settings described above, the Universe IID will power up in a state where VMEbus
accesses with A24 AM codes, in the address range 0x0-0xFFF, will map into Universe II registers.

The VME_RAI will be utilized to set up the VMEbus slave images described below.

VMEbus Slave Image 0

In this configuration example, the VMEbus Slave Image 0 is set up to map A16 supervisory
accesses, in the address range 0x0-0x4FFF, from VMEbus to Configuration Cycles on the PCI bus.

1) This column shows write data for configuration from PCI

TABLE B-1.

VME_RAI Setup

Action:

Result:

SW3-3 ON

VME_RAI is enabled.

SW3-1 ON, SW3-2 OFF

VME_RAI is mapped in A24 address space.

SW5 All OFF

VME_RAI base address is set to 0x000000.

SW11-2 OFF

Disable Auto-slot ID protocol.

TABLE B-2.

VME Slave image 0 - setup

Write from VME

PCI Data 1)

Result:

D:0x0000.0000 to A:0x000F04

0x0000.0000

Base Address set to 0x000000

D:0x0050.0000 to A:0x000F08

0x0000.5000

Bound Address set to 0x005000

D:0x0000.0000 to A:0x000F0C

0x0000.0000

Translation Offset set to 0x000000

D:0x0200.E080 to A:0x000F00

0x80E0.0002

Enable Image, VAS=A16, LAS=Config Space,
PGM=both, SUPER=Supervisor, other options
disabled.

«
...
94
95
96
97
98
...
»

Содержание M5210RP-EFF



































































































































Отзывы:

Нет отзывов