Vmetro M5210RP-EFF Скачать руководство пользователя страница 89

Страница: 89 / 130

Issued June 20, 2007

M5000 Series: User Guide

Miscellaneous PLD Registers

PPC_BOOT

RST_SERIAL

MISC

PPC_BOOT_SPROM_WE#

PowerPC Boot SPROM devices are write-protected (1) or
enabled (0) (Read-Only)

PPC_SPROM_WE#

PowerPC MFS SPROM device is write-protected (1) or
enabled (0) (Read-Only)

PPC_FLASH_MON_WE#

PowerPC FLASH device (Monitor part) is write-protected (1)
or enabled (0) (Read-Only)

PPC_FLASH_WE#

PowerPC FLASH device is write-protected (1) or enabled (0)

(Read-Only)

FC_FLASH_WE#

QLOGIC ISP2312 FLASH device is write-protected (1) or
enabled (0) (Read-Only)

PPC_BOOT

PowerPC loads boot parameters from PCI Boot SROM (0) or
from FLASH Boot SPROM (1) (Read-Only)

PPC_ECC

PowerPC processor uses ECC memory bank (0) or not (1)
(Read-Only)

ECO_SPROM_WE#

ECO SPROM device is write-protected (1) or enabled (0)
(Read-Only)

Note: Only present from ECO C1

SYS_RST

System Reset: Set this bit to 1 to reset the entire board without resetting the
entire VME rack (Write-Only)

RCLK_66

RACEway Clock 66MHz: set to 1 if RACEway clock is a 66MHz clock, 0
otherwise (Read-Only)

RCLK_DET

RACEway Clock Detection: set to 1 if RACEway clock is detected, 0 otherwise
(Read-Only)

MEZZ_ID2

3-bit mezzanine identifier (Read-Only)

MEZZ_ID1

3-bit mezzanine identifier (Read-Only)

MEZZ_ID0

3-bit mezzanine identifier (Read-Only)

PMC1_MON

PMC Site #1 MONARCH#: set to 0 if the PMC#1 site is setup as MONARCH, 0
otherwise (Read-Only)

PMC1_PRES

PMC Site #1 Present: set to 1 if a PMC module is located in PMC site #1, 0
otherwise (Read-Only)

PMC_ERDY

PMC Site Ready: set to 1 if all the PMC sites are ready, 0 otherwise (Read-Only)

Содержание M5210RP-EFF



































































































































Результаты поиска

Содержание M5210RP-EFF

Отзывы:

Vmetro M5210RP-EFF, Руководство пользователя, Страница: 89 / 130

Результаты поиска

Содержание M5210RP-EFF

Отзывы: