Vmetro M5210RP-EFF Скачать руководство пользователя страница 63

Страница: 63 / 130

M5000 Series: User Guide

Issued June 20, 2007

Mezzanine PMC Carrier

Precautions in Handling and Storage

Static electricity can cause permanent damage. Prevent
electrostatic damage by taking proper precautions.

•

Make sure your body is grounded when coming into contact
with the board by wearing an anti-static wrist strap.

•

If an anti-static wrist strap is not available, touch a grounded
surface, such as the bare metal chassis, before touching the
M52xx and Mezzanine PMC Carrier board.

•

Only leave the board on surfaces with controlled static
characteristics, i.e. specially designed anti-static table covers.

•

When handing the board to another person, first touch this
person’s hand, wrist etc. to discharge any static potential.

•

Always store the board in an anti-static bag or other static
resistant container.

•

If an electric screwdriver is used, it should be grounded and
shielded to prevent sparks.

Part Numbers referred to in this chapter:

•

MEZZ-x500F - Mezzanine PMC Carrier board (3 PMC Slots)

•

M52xx - The base board (2 PMC Slots)

•

M55xx - The combination of base board and carrier board (5
PMC Slots)

Содержание M5210RP-EFF



































































































































Результаты поиска

Содержание M5210RP-EFF

Отзывы:

Vmetro M5210RP-EFF, Руководство пользователя, Страница: 63 / 130

Результаты поиска

Содержание M5210RP-EFF

Отзывы: