Vmetro M5210RP-EFF Скачать руководство пользователя страница 31

Страница: 31 / 130

Issued June 20, 2007

M5000 Series: User Guide

Switches and Jumper Settings

PCI-X Capability Selection for PMC Slots

The PCI-X Capability Selection is performed using the switches SW1 and SW4.

•

Switch 1

configures PMC#2 bus

•

Switch 4

configures PMC#1 bus

Jumper Settings

This section describes the role and use of the configuration jumpers located on the board.

PCI-to-RACEway Bridge Reset

The PCI-to-RACEway Bridge Reset configuration is done using jumper JP1.

Jumper inserted on the left side:

•

Reset on RACEway interface cause the board to reset

•

Board reset does not generate a RACEway reset.

Jumper inserted on the right side:

•

Reset on RACEway interface cause the PXB to reset.

•

Board reset generates a RACEway reset.

Processor Boot Serial EEPROM Download

During the board configuration, the two Processor Boot Serial EEPROM devices are written using
jumper JP3. This jumper is not used during normal operations.

ECO Serial EEPROM

Insert a jumper in JP2 to write enable the ECO Serial EEPROM.

TABLE 2-9.

PCI-X Capability Selection SW1(PMC#2) and SW4(PMC#1) settings

PCI(-X) Configuration

Note

PCI-X / 133MHz

OFF

PCI-X / 100MHz

OFF

PCI-X / 66MHz

OFF

PCI / 66MHz

OFF

PCI / 33MHz

Содержание M5210RP-EFF



































































































































Результаты поиска

Содержание M5210RP-EFF

Отзывы:

Vmetro M5210RP-EFF, Руководство пользователя, Страница: 31 / 130

Результаты поиска

Содержание M5210RP-EFF

Отзывы: