VKI Technologies KEURIG Eccellenza touch Скачать руководство пользователя страница 101

Страница: 101 / 108

ecti

on
5 –

rro
r M
es

sages

Eccellenza Touch

VKI Publication #100308-003

101

Code

Message Displayed

Condition

Action(s) Required

Heater's current is close to critical

level

Heater current is close to maximum

operating level. Heater may be

drawing too much power.

1 - Inspect wiring and connections

to the heater relay and heater

element.

2 - Heater element may be drawing

too much power. If message

persists, replace the heater element.

Heater's current is close to minimum

operation level

Heater current is close to minimum

operating level. Heater may not be

drawing enough power.

1 - Reboot the machine.

2 - If message persists, replace the

heater element.

Heater's current is over safety level Heater current has exceeded the

maximum operating level.

1 - Inspect wiring and connections

to the heater relay and heater

element.

2 - Heater element may need to be

replaced.

3 - Heater relay may need to be

replaced.

Heater's current is under minimum

operation level

Heater current is below the

minimum operating level.

1 - Check wiring and connections to

the heater relay.

2 - Check wiring and connections to

the heater element.

3 - Replace heater element.

Water Tank Default

Critical Min Temp

Water temperature went below the

configured minimum critical

temperature (Default 0 C).

1 - Clear the message.

2 - Reboot the machine.

Water Tank Default Fill

Heating Time

Inlet valve and heater were both

activated for a period of time longer

than the configured timeout.

1 - Clear the message.

2 - Reboot the machine.

Water Tank Heating

Timeout

Reaching the water set point

(Default 95°C) took longer than the

maximum configured heating

timeout (Default: 30 min.)

1 - Clear the message.

2 - Reboot the machine.

3 - If message persists, replace the

heater element.

Water Tank Heating Probe

Error

Heater bad connection count has

exceeded the configured limit.

1 - Clear the message.

2 - Reboot the machine.

Water temperature is over the

maximum level

Water temperature has exceeded

configured temperature setting.

1- Heater relay may need to be

replaced.

2 - Control board may need to be

replaced.

K1 Fan is not present or has abnormal

operation

Fan is not present or operating

abnormally.

1 - Check fan wiring and connection

to the control board.

2 - Clean any accumulation from fan.

3 - If message persists, replace the

exhaust fan.

4 - If message persists, replace the

control board.

Water Tank Level Error

Safety level probe is detected while

the normal level probe is not.

1 - Check wiring and connections to

the level probes.

2 - Clean level probes.

The water level is reaching the

safety level probes

The water tank has overfilled and

the water level is reaching the safety

level probe.

1 - If this occurs during initial

heating, it may be due to water

expansion. Empty some water from

tank.

2 - The machine may have been

moved causing tank to overfill.

Empty some water from tank.

3 - Level probes require cleaning.

MDB1

Cash Box Full

The cash box in the changer housing

is full.

1 – Empty the cash box.

2 – Reset the Cash Box counter.

Coin Changer…(various messages)

Miscellaneous Coin Changer-related

issues.

Consult the coin changer

manufacturer’s documentation.

Содержание KEURIG Eccellenza touch













































































































Результаты поиска

Содержание KEURIG Eccellenza touch

Отзывы:

Похожие инструкции для KEURIG Eccellenza touch

Бренды по названию

Популярные бренды

VKI Technologies KEURIG Eccellenza touch, Руководство по эксплуатации

Результаты поиска

Содержание KEURIG Eccellenza touch

Отзывы:

Похожие инструкции для KEURIG Eccellenza touch

Бренды по названию

Популярные бренды