VKI Technologies Eccellenza touch Скачать руководство пользователя страница 6

Страница: 6 / 68

ecti

on 1

- S

ety

orma

tion

& E

ipmen

t S

pecif

ications

Service Manual

VKI Publication #100309-001

Important Safeguards and Precautions



This equipment is designed for indoor use

ONLY

and must

never

be installed outdoors.



The installation of this equipment must comply with all municipal, state/provincial, and

federal electrical and plumbing codes.



Installation and servicing of this equipment must only be performed by qualified

personnel. Do not attempt to install or service this equipment if you are not qualified as

it may result in personal injury. There are no user-serviceable parts inside the

equipment.



Do not use an electrical extension cord or power bar.



This equipment must be installed in a location with an ambient temperature between

5°C-35°C (40°F-95°F).



The main water supply pressure must be between a minimum of 20psi and a maximum

of 100psi.



This equipment must be positioned so that the wall plug and the main power switch are

both easily accessible.



Do not connect this equipment to a voltage supply other than the voltage indicated on

the serial number decal.



Do not immerse this equipment, or any part of this equipment, in liquid.



Do not install the equipment in an area where water spray is present.



This equipment must be installed securely on a level surface. If it does not appear to be

a stable location, select another installation location.



Leave a

minimum of 2" (5cm)

of space around this equipment for proper ventilation.



Keep hands clear of the dispensing area at the front of this equipment. Liquids being

dispensed are extremely hot and can cause severe burns.



Never

disconnect this equipment from the wall outlet by pulling on the service cord,

and never use this equipment if the service cord is damaged.



If the service cord is damaged,

it must be replaced with a new service cord

that is

available from your distributor or the manufacturer of this equipment.



Never

circumvent the safety features incorporated into the equipment. They are there

for your protection and

should never be disabled or bypassed under any

circumstances



Always

switch the power off and disconnect the service cord when cleaning the interior

of this equipment. Components inside this equipment can cause electrical shock

resulting in personal injury.

Содержание Eccellenza touch





































































Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza touch, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды