VKI Technologies Eccellenza touch Скачать руководство пользователя страница 16

Страница: 16 / 68

ecti

on 3

- E

rro

r & Rem

inder M

sages

Service Manual

VKI Publication #100309-001

Message Displayed

Code

Condition

Action(s) Required

Water temperature is not rising while

heating

Water temperature is not increasing

while in heating mode.

1 - Check wiring and connections to

heater relay, heater element and

control board.

2 - Heater relay may need to be

replaced.

3 - Heater element may need to be

replaced.

4 - Control board may need to be

replaced.

Water temperature is over the

maximum level

Water temperature has exceeded

configured temperature setting.

1- Heater relay may need to be

replaced.

2 - Control board may need to be

replaced.

Whippers current is close to critical

level

M4,

M5,

M11

Powder Whipper current is close to

maximum operating level.

1 - If message persists, replace the

faulty whipper motor.

Whippers current is close to minimum

operation level

M4,

M5,

M11

Powder Whipper current is close to

minimum operating level.

1 - If message persists, replace the

faulty whipper motor.

Whippers current is over safety level

M4,

M5,

M11

Powder Whipper current has

exceeded the maximum operating

level.

1 - If message persists, replace the

faulty whipper motor.

Whippers current is under minimum

operation level

M4,

M5,

M11

Powder Whipper current is below

the minimum operating level.

1 - Check the wiring and connections

to the whipper motor.

2 - If message persists, replace the

faulty whipper motor.

Wiper current is over safety level

M10

The wiper motor current was over

the configured maximum operation

level.

1 - The wiper may be jammed or

binding.

2 - The wiper motor may need to be

replaced.

Wiper current is under minimum

operation level

M10

The wiper motor current was under

the configured minimum operation

level.

1 - The wiper may be missing or

improperly installed.

2 - Check wiper motor connections.

3 - The wiper motor may need to be

replaced

Wiper Inversion

M10

The wiper limit switches are

inverted.

1 - Reverse the wiring connections

to the wiper switches.

Wiper Not Initialized

M10

A wiper sequence was started while

the wiper was not initialized

(homed).

1 - Clear the message.

2 - Reboot the machine.

3 - If message persists, check wiper

motor switches and connections.

4 - If message persists, a wiper

motor switch needs to be replaced.

Wiper Over Current

Standby

M10

The wiper current was over the

configured stand by operation level.

1 - Clear the message.

2 - Reboot the machine.

Wiper Safety Fault

M10

The IC of the wiper driver is in fault

mode.

1 - Reboot the machine.

2 - If message persists, the control

board may need to be replaced.

Wiper Timeout

M10

Wiper motion is timed out: brewer

is moving too slow (or stopped),

unable to reach required position in

the allotted period of time.

1 - The wiper may be jammed or

binding.

2 - Check wiper motor connections.

3 - The wiper motor may need to be

replaced.

Wiper Unexpected Item

Received

M10

A wiper sequence step was received

while a wiper sequence was already

in progress.

1 - Clear the message.

2 - Reboot the machine.

Содержание Eccellenza touch





































































Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza touch, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды