VKI Technologies Eccellenza touch Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 68

background image

S

ecti

on 6

- Wat
er S

ys

tem

Eccellenza Touch

VKI Publication #100309-001

47

Removing the Water Tank

1.

With the water tank drained and the service cord disconnected, remove the thermal

tape from the valves, and disconnect the power wires from each of the valves.

2.

Disconnect the outlet hoses from each of the outlet valves.

3.

Disconnect the inlet hose (coming from the inlet valve).

4.

Pull the tank towards you and partially out of the machine - you need to get access to

the tank top.

5.

Disconnect the wiring from the heating element.

6.

Disconnect the wiring from the three level probes.

7.

Disconnect the inline connector to the temperature probe.

8.

Pull the water tank completely out of the machine.

You will need to remove the overflow hose from the upper and lower

openings in the metal through which the hose is routed.

Replacing the Temperature Probe and Water Level Probes

1.

With the water tank removed, pull the temperature probe and/or the water level

probes out through the top of the tank lid. They are simply clipped in place.

2.

Slide the new temperature probe and/or water level probes completely into the tank

lid until they are clipped and locked in position.

«
...
45
46
47
48
49
...
»

Содержание Eccellenza touch





































































Отзывы:

Нет отзывов

Похожие инструкции для Eccellenza touch

Grill ECO AIR-PROFI SOUP DC-1400W

Бренд: 1A Profi Handels Страницы: 2

Бренд: U-Line Страницы: 28

Бренд: Xiamen Hanin Electronic Technology Страницы: 102

Бренд: Gaggia Страницы: 61

KITCHEN PRO K6725

Бренд: Regal Ware Страницы: 62

Бренд: FlyTek Страницы: 22

Бренд: Custom Audio Electronics Страницы: 2

KM 160 Minimo Premio

Бренд: ECG Страницы: 98

Бренд: Omcan Страницы: 20

Бренд: Krups Страницы: 11

FUTURMAT SENSIUS

Бренд: Quality Espresso Страницы: 44

GS-3405T Series

Бренд: Gainscha Страницы: 35

2 lb. EXPRESSBAKE recip

Бренд: Oster Страницы: 76

Бренд: QuickLabel Systems Страницы: 485

Бренд: G&G Страницы: 3

Бренд: Salente Страницы: 32

Бренд: Klarstein Страницы: 36

Бренд: Hamilton Beach Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды