VKI Technologies Eccellenza touch Скачать руководство пользователя страница 68

Страница: 68 / 68

ecti

- U

ating Fi

rmw

are

Service Manual

VKI Publication #100309-001

The updating process is automated and requires no user input. The screen reverts to

command-style prompts that provide progress information on the update.

Once the update is complete (after 5-10 minutes), you are prompted to remove the

USB flash drive to reboot the machine.

Remove the flash drive and the Eccellenza Touch will reboot itself twice. While it is

rebooting, re-install the plug onto the USB connector and re-install the waste bin.

It is possible that an error may be displayed on the screen. If this is the case, simply

clear the error.

Updating the Eccellenza Touch firmware will not overwrite or change any

existing settings or customizations you may have made in the programming.

These settings will be maintained.

Содержание Eccellenza touch





































































Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza touch, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды