VKI Technologies Eccellenza touch Скачать руководство пользователя страница 67

Страница: 67 / 68

ecti

on
8 -

ating

firmw

are

Eccellenza Touch

VKI Publication #100309-001

E C T I O N

Updating Firmware

Firmware updates may be released periodically for the Eccellenza Touch. These updates may

consist of fixes, new options and features, customizations, etc. This section guides you through

the simple process of updating your equipment to the latest firmware.

After replacing the control board, the firmware must be loaded when the

machine is first powered up. Do not power up the machine until the USB

Flash drive with the proper firmware is connected to the machine.

Load the latest firmware files onto a USB flash drive (minimum 1GB).

Remove the waste bin.

Remove the plug from the USB connector and insert your USB flash drive into it.

Make

sure to push the USB flash drive into the USB connector as far as it can go.

Reboot the machine using the main power switch.

Содержание Eccellenza touch





































































Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza touch, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды