VKI Technologies Eccellenza touch Скачать руководство пользователя страница 44

Страница: 44 / 68

ecti

on 5

- Cof

fee

der

tems

Service Manual

VKI Publication #100309-001

When replacing the

impeller

, align the small arrow on the impeller with the flat side of the

whipper shaft. Push the impeller until it clicks in place.

Powder Rinse

After servicing the whipper system, you'll need to perform a 'Powder Rinse' to flush powder that

may have fallen into any of the three whippers.

Go to the

'System Status'

screen and select the

'Maintenance'

tab.

Tap the '

Powder Rinse

' option to activate it.

This option runs a rinse cycle (to clean all three of the powder whipper systems) by sending hot

water through each of the whipper units, while at the same time activating each of the whipper

motors.

Place a cup on the cup stand prior to running this cycle as up to 12-oz of

water will be dispensed once the cycle is activated.

Содержание Eccellenza touch





































































Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza touch, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza touch

Отзывы:

Похожие инструкции для Eccellenza touch

Бренды по названию

Популярные бренды