background image

Page | 23 
 
 

Handy Hints for Foiling 

 

PLEASE NOTE THIS IS A GUIDE ONLY 

 

 

Using a coated paper will be far easier to foil than uncoated.  

 

If foiling onto laminating stocks, please ensure you have used a corona treated printable film. 

 

Laminate can change the thickness of the paper, take note of your printer specifications. 

 

Duplex and Pneumatic Models

 

 

Media to be Foiled 

Temperature (°C/°F) 

Pressure (Bar) 

Laminated paper 

90-95/194-203 

0-0.4 

Printable foil on Laminated paper 

90-95/194-203 

0-0.4 

Coated paper 

100-105/212-221 

0.4-1 

Printable foil on coated paper 

90-100/194-203 

0.3-0.4 

Uncoated paper  

105-115/221-239 

0.6-0.8 

Printable foil on uncoated paper 

100-105/212-221 

0.4-0.6 

 

 

Metallic Models

 

 

Media to be Foiled 

Temperature (°C/°F) 

Pressure (Bar) 

Laminated paper 

130-135/266/275 

0.6-1.0 

Printable foil on Laminated paper 

120-125/248-257 

0.8 

Coated paper 

135/275 

0.8 

Printable foil on coated paper 

120-125/248-257 

0.8 

Uncoated paper  

135-140/275-284 

0.8-1.0 

Printable foil on uncoated paper 

120-130/248-257 

0.8-1.0 

 

 

 

 

 

 

 

 

 

Содержание Matrix 530DP

























Отзывы: