background image

Page | 21 
 
 

 

 

 

 

 

 

 

 

 

 

Timing is very important for the splitting process. The splitter/separator roller must come down after the sheet has finished 
perforating and come up before the next sheet comes. For speeds of 0.5-2mmpm the display separator/cutting adjustment should 
be set to 0. See below for guide. 

 

0.5-2mmpm = 0 

 

 2-4.5mmpm = -20 

 

5mmpm and above = -40 

 

Speed & Temperature Control 

 

 

 

Most BOPP/OPP films operate between 95

o

C and 125

o

C. Ensure the  

Matrix is at the set temperature before you start to laminate. If your print 

is silvering/cloudy the film has not properly bonded to the media you are: 

 

either running the system to fast 

 

not hot enough 

 

the pneumatic pressure is not set correctly. 

If your print appears blistered or the film has shrunk significantly as it passes over the laminating roller your running the system 
too hot or not fast enough. 

  

We recommend 105

o

C at speeds of 2.5mmpm, pressure for the laminating roller set to full and pull  

roller set between 0.2 – 0.4.  

 

If the paper creases as it exits the laminating roller then reduce the pressure on the laminating roller until the crease disappears. 

 

Depending on the film you are using your prints might require a curing time after printing/laminating, ensure the sheets have no 
heat from the printing/laminating before you start the next process. 

Содержание Matrix 530DP

























Отзывы: