Villeroy & Boch A5L Скачать руководство пользователя

Страница: 20 / 51

JETS 2

LIGHT

JETS 1

HEAT

JETS 2

JETS 1

LIGHT

SELECT

Preparation and Filling

Fill the spa to its correct operating level. (See SPA

MAINTENANCE section of this manual.) Be sure to open all

valves and jets in the plumbing system before filling to allow as

much air as possible to escape from the plumbing and the control

system during the filling process. After turning the power on at

the main power panel, the control panel display will go through

specific sequences. These sequences are normal and display a

variety of information regarding the configuration of the hot tub

control. After a few seconds, the spa will go into priming mode

and will display “PR”.

Priming the Pumps

As soon as the priming mode menu appears on the panel, press

the

“Jets 1” button once to start Pump 1 in low-speed and

then again to switch to high-speed. Next, if your spa is equipped

with a second pump press the Jets 2 or “Aux” button twice, to

turn it on high. The pumps will now be running in high-speed to

facilitate priming.

IMPORTANT:

A pump should not be allowed to run

without priming (water flowing out of the jets) for more than 2

minutes. Under NO circumstances should a pump be allowed to

run without priming beyond the end of the 4-5 minute priming

mode. Doing so may cause damage to the pump and cause the

system to energize the heater and go into an overheat condition.

NOTE:

Turning the power off and back on again will initiate a

new pump priming session. Sometimes momentarily turning the

pump off and on will help it to prime. Do not do this more than

5 times. If the pump(s) will not prime, shut off the power to the

spa and call for service.

Exiting Priming Mode

You can manually exit Priming Mode by pressing the

button. Note that if you do not manually exit the priming mode

as described above, the priming mode will automatically end

after 4-5 minutes. Be sure that the pump(s) have been primed by

this time. Once the system has exited Priming Mode, the control

panel will momentarily display the set temperature. The system

requires approximately 1-2 minutes of water flowing through the

heater to determine and display the correct water temperature.

Light Operation

By turning the light on and off, it will change the sequence of

colors from flashing, to fading, to solid color. Use the light button

COMFORT LINE SPAS

JETS 2

LIGHT

JETS 1

HEAT

JETS 2

JETS 1

LIGHT

SELECT

Jets 1

Press to toggle jets

LOW/HIGH/OFF

Jets 2

Press to toggle jets

LOW/HIGH/OFF (for

spas equipped with

dual pumps)

Lights Toggle

Press to toggle lights

ON/OFF

Down Button

Used to move through

menu selections

Up Button

Used to move through

menu selections

Menu/Select

Used to make

menu selections

2016 V&B Owners Manual.indd 20

3/3/2016 1:46:09 PM

Содержание A5L




















































Результаты поиска

Содержание A5L

Отзывы:

Похожие инструкции для A5L

Бренды по названию

Популярные бренды

Villeroy & Boch A5L, Быстрая справка

Результаты поиска

Содержание A5L

Отзывы:

Похожие инструкции для A5L

Бренды по названию

Популярные бренды