Villeroy & Boch A5L Скачать руководство пользователя

Страница: 10 / 51

WARNING:

An empty spa (spa without water in it) must not

be left exposed to sunlight as shell damage may occur. Once the spa

is unwrapped, fill spa with water immediately or shade the spa with

cover or wrapping to prevent direct exposure to sunlight.

IMPORTANT:

Do not turn power on to the spa without water

in the spa. Serious damage to the pump and heater may occur.

Step 1:

Fill the Spa: Use a garden hose to fill the spa to the water

level indication mark on the faceplate of the filter weir assembly.

Be sure to open all valves and jets in the plumbing system before

filling to allow as much air as possible to escape from the plumbing

during the filling process.

NOTE:

For complete filling instructions, refer to Changing Spa

Water (page 30).

IMPORTANT:

Never fill the spa with soft water unless an

appropriate mineral supplement is immediately added (see your

authorized Villeroy & Boch Dealer). If your water is extremely

hard, it is preferable to either dilute the water’s hardness by

blending the water with water from a water softener, or by the

addition of a special water softening chemical (see your authorized

Villeroy & Boch Dealer).

Step 2:

Check for Leaks: After the spa is filled, check all fittings

and equipment in equipment compartment for signs of leakage

before turning on the spa. Turn on pump(s), once again, check for

leakage. If a leak is detected, tighten the fitting by hand. If the leak

persists contact your authorized Villeroy & Boch Dealer.

Step 3:

Install Cover: The spa cover comes with tie down

straps and locking hardware that attaches the cover to the spa or

decking. If your dealer did not install the cover, refer to the Cover

Installation Instructions included with the cover.

Cover locks are an essential component for compliance with the

safety standard for spa covers.

Control System

IMPORTANT :

Your Villeroy & Boch Spa is equipped with

one of 4 types of control pads: A900 (5 Button), R600 (5 or 6

Button), X300 (3 or 4 Button)or Touch Screen. Locate the control

system on your spa by matching it with the photo provided under

each control panel section and follow the specific instructions for

operation of your specific control system.

Your spa is pre-programmed with default filter cycles and

temperature settings. The following control panel instructions will

detail the procedures to alter such default settings.

FILLING YOUR SPA

2016 V&B Owners Manual.indd 10

3/3/2016 1:45:32 PM

Содержание A5L




















































Результаты поиска

Содержание A5L

Отзывы:

Похожие инструкции для A5L

Бренды по названию

Популярные бренды

Villeroy & Boch A5L, Быстрая справка

Результаты поиска

Содержание A5L

Отзывы:

Похожие инструкции для A5L

Бренды по названию

Популярные бренды