Villeroy & Boch A5L Скачать руководство пользователя

Страница: 42 / 51

General Messages

Most messages and alerts will appear on the main screen. Several alerts and messages may be displayed in a sequence. Some messages

can be reset by pushing the “jets” button.

– – –°F – – –°C

Water Temperature is Unknown

After the pump has been running for 1 minute, the temperature will be displayed.

Possible freezing condition

A potential freeze condition has been detected. All water devices are activated. In some cases, pumps may turn on and off and the

heater may operate during

Freeze Protection.

This is an operational message, not an error indication.

The water is too hot

The system has detected a spa water temp of 110°F (43.3°C) or more, and spa functions are disabled. System will auto reset when the

spa water temp is below 108°F (42.2°C). Check for extended pump operation or high ambient temp.

Heater-Related Messages

The water flow is low

There may not be enough water flow through the heater to carry the heat away from the heating element. Heater start up will begin

again after about 1 min.

See “Flow Related Checks” below.

The water flow has failed*

There is not enough water flow through the heater to carry the heat away from the heating element and the heater has been disabled.

See “Flow Related

Checks” below. After the problem has been resolved, you must press any button to reset and begin heater start up.

The heater may be dry*

Possible dry heater, or not enough water in the heater to start it. The spa is shut down for 15 min. Press any button to reset the heater

start-up. See “Flow

Related Checks” below.

The heater is dry*

There is not enough water in the heater to start it. The spa is shut down. After the problem has been resolved, you must clear the

message to restart heater start

up. See “Flow Related Checks” below.

The heater is too hot*

One of the water temp sensors has detected 118°f (47.8°C) in the heater and the spa is shut down. You must clear the message when

water is below 108°f

(42.2°C). See “Flow Related Checks” below.

Flow-Related Checks

Check for low water level, suction flow restrictions, dirty filters, trapped air, too many closed jets and pump prime. On some systems,

even when spa is shut

down by an error condition, some equipment may occasionally turn on to continue monitoring temperature or if freeze protection is

needed.

•

This message can be reset from the control panel.

Sensor-Related Messages

2016 V&B Owners Manual.indd 42

3/3/2016 1:46:53 PM

Содержание A5L




















































Результаты поиска

Содержание A5L

Отзывы:

Похожие инструкции для A5L

Бренды по названию

Популярные бренды

Villeroy & Boch A5L, Быстрая справка

Результаты поиска

Содержание A5L

Отзывы:

Похожие инструкции для A5L

Бренды по названию

Популярные бренды