Viking DDSF036SS Скачать руководство пользователя | Manualshive

Страница: 39 / 58

background image

Service Procedure

©2007 Viking Preferred Service

39

Charging

NOTE

: Do not use captured or recycled refrigerant in

units. Captured or recycled refrigerant voids any
warranty.

NOTE

: Charge system with exact amount of refrigerant.

Refer to unit serial plate for correct refrigerant
charge. Inaccurately charged system will cause
future problems.

To charge system:
Close valves “A” to vacuum pump and “C” to vacuum
gauge and “E” to low side manifold gauge.
1. Set scale on dial-a-charge cylinder for corresponding

HFC134a pressure reading.

2. Open valve “F” to charging cylinder and let exact

amount of refrigerant flow from cylinder into system.
Close valve.
Low side gauge pressure should rise shortly after
opening charging cylinder valve as system pressure
equalizes through capillary tube.
If pressure does not equalize, a restriction typically
exists at capillary/drier braze joint.

3. If pressure equalizes, open valve “E” to low side

manifold gauge and pinch off high side drier process
tube.

4. Start compressor and draw remaining refrigerant

from charging hoses and manifold into compressor
through compressor process tube.

5. To check high side pinch-off drier process tube.

Close valve “D” to high side gauge. If high side
pressure rises, repeat high side pinch-off and open
valve “D”. Repeat until high side pinch-off does not
leak.

6. Pinch-off compressor process tube and remove

charging hose. Braze stub closed while compressor
is operating.

7. Disconnect power. Remove charging hose and braze

high side drier process tube closed.

8. Recheck for refrigerant leaks.

Refrigerant Charge

Refrigerant charge in all capillary tube systems is critical
and exact amount is required for proper performance.
Factory charges are shown on serial plate.

NOTE:

Do not use refrigerant other than shown on
serial plate.

HFC134a Service Information

HFC134a is alternative refrigerant for CFC12.
HFC134a has an ozone depletion potential (ODP) factor
of 0.0 and a global warming potential (GWP) factor of
0.27. HFC134a is not flammable and has acceptable
toxicity levels. HFC134a is not interchangeable with
CFC12. There are significant differences between
HFC134a and CFC12 which must be considered when
handling and processing refrigeration system.

Health, Safety, and Handling

Health, safety and handling considerations for HFC134A
are virtually no different than those for CFC12.

Health, Safety, and
Handling

CFC12 HFC134a

Allowable overall
exposure limit

1,000 ppm

Same

Vapor exposure to skin

No effect

Same

Liquid exposure to skin

Can cause frostbite

Same

Vapor exposure to eye

Very slight eye irritant

Same

Liquid exposure to eye

Can cause frostbite

Same

Above minimum
exposure limit

Can cause Asphyxiation,

Tachycardia, and Cardia

Arrhythmias

Same

Safety and handling

Wear appropriate skin

and eye protection. Use

with adequate

ventilation.

Same

Spill management

Remove or extinguish
ignition or combustion

sources. Evacuate or

ventilate area.

Same

Fire explosion hazards May

decompose

if

contact with flames and

heating elements.

Container may explode

if heated due to resulting

pressure rise.

Combustion products

are toxic.

Same

Disposal procedures

Recycle or reclaim.

Same

«
...
37
38
39
40
41
...
»

Содержание DDSF036SS



























































Отзывы:

Нет отзывов

Похожие инструкции для DDSF036SS

Бренд: Daewoo Страницы: 38

Бренд: Norcold Страницы: 4

Бренд: NEFF Страницы: 32

Бренд: Jenn-Air Страницы: 68

Бренд: Maytag Страницы: 66

Бренд: U-Line Страницы: 44

Party Fridge MC-88M

Бренд: Soleus Air Страницы: 6

Бренд: Parmco Страницы: 7

Бренд: Daewoo Страницы: 18

Бренд: Küppersbusch Страницы: 12

Бренд: EvaKool Страницы: 6

CoolMatic CRX50

Бренд: Waeco Страницы: 33

Бренд: Fagor Страницы: 68

Бренд: Hanseatic Страницы: 74

Бренд: Sauber Страницы: 52

Бренд: Dometic Страницы: 40

Бренд: Haier Страницы: 13

Бренд: Alto-Shaam Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды