Viessmann Vitocaldens 222-F Скачать руководство пользователя страница 2

Страница: 2 / 60

Please follow these safety instructions closely to prevent accidents and
material losses.

Safety instructions explained

Danger

This symbol warns against the
risk of injury.

Please note

This symbol warns against the
risk of material losses and envi-
ronmental pollution.

Note

Details identified by the word "Note"
contain additional information.

Target group

These instructions are exclusively
intended for authorised contractors.
■ Work on gas installations must only

be carried out by a registered gas fit-
ter.

■ Work on electrical equipment must

only be carried out by a qualified
electrician.

Regulations to be observed

■ National installation regulations
■ Statutory regulations for the preven-

tion of accidents

■ Statutory regulations for environmen-

tal protection

■ Codes of practice of the relevant

trade associations

■ All current safety regulations as

defined by DIN, EN, DVGW, TRGI,
TRF, VDE and all locally applicable
standards

ÖNORM, EN, ÖVGW-TR Gas,
ÖVGW-TRF and ÖVE

SEV, SUVA, SVGW, SVTI,
SWKI, VKF and EKAS guideline
1942: LPG, part 2

Working on the system

■ Isolate the system from the power

supply (e.g. by removing the sepa-
rate fuse or by means of a mains iso-
lator) and check that it is no longer
'live'.

■ Safeguard the system against recon-

nection.

■ Where gas is used as the fuel, close

the main gas shut-off valve and safe-
guard it against unintentional reopen-
ing.

Safety instructions

5780 223 GB

Содержание Vitocaldens 222-F





























































Результаты поиска

Содержание Vitocaldens 222-F

Отзывы:

Похожие инструкции для Vitocaldens 222-F

Бренды по названию

Популярные бренды

Viessmann Vitocaldens 222-F, Руководство по установке

Результаты поиска

Содержание Vitocaldens 222-F

Отзывы:

Похожие инструкции для Vitocaldens 222-F

Бренды по названию

Популярные бренды