Viessmann Vitocaldens 222-F Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 60

background image

10

Boiler position

The following limitations must be
observed when siting the boiler:
■ The boiler is not suitable for external

installation. The position selected for
the installation should be within the
building, unless otherwise protected
by a suitable enclosure and must
allow adequate space for installation,
servicing and operation of the appli-
ance and for air circulation around it.

■ The position must allow for a suitable

flue system and terminal position.
The boiler must be installed on a flat
vertical wall capable of supporting the
weight of the appliance and any
ancillary equipment when full.

■ Due consideration should be given to

the routing of the condensate drain
from the chosen position.

■ If the boiler is to be fitted in a timber

framed building it should be fitted in
accordance with ige/up/7. If in doubt
advice must be sought from the Insti-
tute of Gas Engineers.

■ If the appliance is to be installed in a

room containing a bath or shower,
any electrical switch or control utilis-
ing mains electricity must be so situ-
ated that it cannot be touched by a
person using the bath or shower.
Attention is drawn to the require-
ments of BS 7671 (the current I.E.E
Wiring Regulations) and in Scotland
the electrical provisions of the Build-
ing Regulations applicable in Scot-
land.

■ A compartment used to enclose the

appliance must be designed and con-
structed specifically for this purpose.
An existing cupboard or compartment
may be used provided it is modified
accordingly. BS 7698:2000 gives
details of the essential features of
cupboard / compartment design,
including airing cupboards. The
Vitodens range does not require
compartment ventilation.

■ Where installation will be in an

unusual location, special procedures
may be necessary. BS 6798 gives
detailed guidance on this aspect.

Installations requirements

(cont.)

5780 223 GB

«
...
8
9
10
11
12
...
»

Содержание Vitocaldens 222-F





























































Отзывы:

Нет отзывов

Похожие инструкции для Vitocaldens 222-F

Бренд: Glow-worm Страницы: 28

Бренд: Sonnenkraft Страницы: 32

Бренд: VHH Страницы: 6

Бренд: Gabarron Страницы: 44

ORLAN SUPER 130 kW

Бренд: Orlanski Страницы: 35

Prestige SOLO 299

Бренд: TriangleTube Страницы: 5

Thermotank UKDAX-160GB25

Бренд: DAXOM Страницы: 29

Бренд: Beretta Страницы: 60

Бренд: Saunier Duval Страницы: 4

Бренд: Viessmann Страницы: 80

Бренд: Saunier Duval Страницы: 20

Бренд: Ferroli Страницы: 20

Бренд: Ferroli Страницы: 32

Бренд: Ferroli Страницы: 60

WarmMaster DeLuxe

Бренд: kochstar Страницы: 12

Бренд: Chaffoteaux & Maury Страницы: 20

CHALLENGER 30 BF

Бренд: Chaffoteaux & Maury Страницы: 24

RAPAX 200 SOL V3

Бренд: Immergas Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды