Viessmann Vitocaldens 222-F Скачать руководство пользователя страница 4

Страница: 4 / 60

Design

Prior to installation, check that the max-
imum possible pipe length will not be
exceeded.
Max. possible pipe lengths in relation to
the boiler used:

Flue systems technical guide

Flue gas temperature protection

The flue pipes are approved for flue
gas temperatures up to 120 °C.

With Viessmann condensing boilers,
internal safeguards ensure that the
maximum permissible flue gas temper-
ature is not exceeded.

Installation information

■ The component overviews for the dif-

ferent types of routing also apply to
floorstanding condensing boilers.

■ Keep flue gas routes short and with

the fewest number of bends possible.

■ Route horizontal connection pipes

with a fall of ≥ 3° (approx. 50 mm/m)
towards the boiler.

■ Support horizontal connection pipes

at intervals of approx. 1 m.

■ To avoid damage and leaks, isolate

the flue system from sources of vibra-
tion (e.g. ventilation systems).

■ Check the gaskets in all female con-

nections are correctly seated.

■ Prior to installation, lubricate all gas-

kets with the lubricating paste provi-
ded.

■ Only use the special gaskets sup-

plied with the boiler.

■ Female plug-in connections in the

flue gas path must always point in the
direction of flow.

■ Only use the components supplied

with the Viessmann flue system.

■ Push the pipes into each other with a

slight twist.

■ Balanced flue pipes can be trimmed

in their assembled state.

Do not carry out

commissioning

until

the following conditions are met:
■ Free passage through the flue gas

pipes.

■ Flue system with positive pressure is

gas-tight.

■ Apertures for ensuring sufficient com-

bustion air supply are open and can-
not be closed off.

■ Applicable regulations on installing

and commissioning flue systems
have been followed.

General installation information

5780 223 GB

Содержание Vitocaldens 222-F





























































Результаты поиска

Содержание Vitocaldens 222-F

Отзывы:

Похожие инструкции для Vitocaldens 222-F

Бренды по названию

Популярные бренды

Viessmann Vitocaldens 222-F, Руководство по установке

Результаты поиска

Содержание Vitocaldens 222-F

Отзывы:

Похожие инструкции для Vitocaldens 222-F

Бренды по названию

Популярные бренды